GEM-P816 Installation Instructions
NAPCO Security Systems
WI994A 10/99
Page 26
%
The GEM-RP1CAe2 Keypad can display the following messages. The GEM-RP2ASe2 will display similar abbreviated messages that
may scroll through two screens. Note: Refer to OI234 for the GEM-RP1CAe2 Keypad; OI192 for the GEM-RP2ASe2 Keypad.
Key
p
ad M
essages
SYSTEM READY - All zones operating; system can be armed.
ARMING YYY/XXX SECONDS - Exit delay in progress. XXX =
exit time remaining in 10-second decrements; YYY = Away, Stay
or Night. Arming then becomes ARMED.
DISARM NOW/XXX SECONDS - Entry delay in progress. XXX =
entry time remaining in 10-second decrements.
SYSTEM ARMED - Panel armed. GEM-RP1CAe2 only.
ZONE FAULTED - One or more zones not secured. Display
status for zone description(s). GEM-RP1CAe2 only.
CAN'T ARM SYSTEM/ZONE FAULTED - Arming attempted with
Priority Zone in trouble. Secure zone to arm.
DAY ZONE TROUBLE - Trouble condition on Day Zone, fol-
lowed by one or more zone descriptions.
INVALID ENTRY/TRY AGAIN - Wrong code/time/area number
entered.
CAN'T ARM SYSTEM/PRESS RESET KEY - Arming attempted
with System Trouble present. Press the
button and then
arm the system.
ALARM - Alarm condition, followed by one or more zone descrip-
tions.
FIRE ALARM - Alarm condition on a Fire Zone. Enter your code
then press the
button to silence the sounder. Correct the
cause of the alarm, then press the
button again. Fire
alarm condition, followed by one or more zone descriptions.
SYSTEM TROUBLE - A System Trouble display will be followed
by one or more of the following error codes:
AC POWER FAIL/E01-00 SERVICE. Power failure. Check
power transformer. Check for blown fuse or circuit breaker;
general power outage.
LOW BATTERY/E02-00 SERVICE. Battery below 11 volts.
If not recharged within 24 hours, replace it.
COMM FAIL/E03-00 SERVICE. Unsuccessful
communication to central station. Note: Will also display if
panel improperly programmed to report; i.e., Report Alarm,
Report Codes, Subscriber ID Numbers, etc. must be
programmed.
WIRELESS TROUBLE/E04-NN SERVICE. Wireless
transmitter supervisory failure. NN = transmitter number.
WIRELESS LOWBATT/E05-NN SERVICE. Rf transmitter
low battery. NN = transmitter number.
SYSTEM TROUBLE/E06-NN SERVICE. Rf receiver
response trouble. NN = receiver number.
SYSTEM TROUBLE/E07-00 SERVICE. Download failure.
SYSTEM TROUBLE/E08-00 SERVICE. Telephone line
failure (system trouble displays after a programmed delay).
SYSTEM TROUBLE/E09-00 SERVICE. System cold start
not programmed after address 1198.
SYSTEM TROUBLE/E10-NN SERVICE. Keypad response
failure. NN = keypad number.
SYSTEM TROUBLE/E11-NN SERVICE. Keypad tamper
cover removed. NN = keypad number.
SYSTEM TROUBLE/E12-NN SERVICE. Expansion zone
module failure. NN = module number.
SYSTEM TROUBLE/E13-NN SERVICE. EZM module cover
removed. NN = module number.
SYSTEM TROUBLE/E15-NN SERVICE. Wireless
transmitter tamper cover removed. NN = transmitter
number.
SYSTEM TROUBLE/E16-NN SERVICE. Receiver jammed.
NN = receiver number.
SYSTEM TROUBLE/E17-NN SERVICE. Receiver cover
removed. NN = receiver number.
SYSTEM TROUBLE/E18-NN SERVICE. Key fob RF
transmitter low battery. NN = key fob transmitter number.
SYSTEM TROUBLE/E19-00 SERVICE. Internal user
memory error. Select RESET SYSTEM TBL. Press the
button, then the
button.
SYSTEM TROUBLE/E20-00 SERVICE. Internal dealer
memory error.
SYSTEM TROUBLE/E22-NN SERVICE. No trip detected on
PIR Supervision Zone within programmed Sensor-Watch
time. NN = Zone number. To reset, press YES (
)
button at “
” function display.
SYSTEM TROUBLE/E23-00 SERVICE. Failure of 4-wire
bus. Check Terminals 11/12.
SYSTEM TROUBLE/E27-NN SERVICE. Check
GEM-Printer Module, printer out of paper or printer off-line.
SYSTEM TROUBLE/E39-00 SERVICE. Receiver capacity
error.
SYSTEM TROUBLE/E41-NN SERVICE. Trouble condition
on a Fire Zone. Press
button to silence the sounder.
Correct the trouble, then press the
button again.
SYSTEM TROUBLE/E51-00 SERVICE - Alarm Output
Supervisory.
NN OUT OF SYSTEM - Keypad inoperative. NN = keypad
number.
FAULT FIND/RF SIGNAL POWER - Fault-find Mode
activated.
