12
Key Fob Transmitters
Keyfobs can be programmed as “Arm/Disarm” devices using the
ON
and
OFF
buttons (refer to control panel installation instructions).
Press the
R
button and for each Key Fob Transmitter, enter:
1
The Key Fob Transmitter number (01–15). Press
R
again.
2
The area number to which transmitter is assigned (1 or 2); enter 0 to
disable keyfob.
3
The 6-digit RF ID # printed on the transmitter (enter all
numbers and/or letters, including leading “0”s, if any).
4
The 1-digit checksum number printed on transmitter.
5
The Aux-1 Option (see key fob Aux 1 & Aux 2 options).
6
The Aux-2 Option (see key fob Aux 1 & Aux 2 options).
Press
U
to save. Then go to step 1 to enter next Key Fob.
When all Key Fobs are entered, press NEXT (
P
) button to
proceed.
Note:
If the Key Fob is converted for Two Button “Emergency Use”
(by cutting an internal jumper), both top or bottom buttons must
be depressed to activate an alarms. In this case, the Aux-1 and
Aux-2 cannot be programmed.
Key Fob Zone Assignment
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 =
point 3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs (using 2 buttons) or 8 key fobs (using all 4
buttons) or any combination up to a maximum of 32 controlled zones can be assigned, providing multiple wireless panic
buttons on a system, each reporting to the Central Station or a pager and/or annunciating on a keypad the key fob zone
number with description/location.
To assign a key fob to a zone:
program the keyfob as you would a transmitter, entering
the keyfob's ID code, check sum and point number at the appropriate zone. The “Quick Method” is not allowed. The
zone may be hardwired to a sensor as well as assigned to a key fob (either one will activate the zone alarm output).
NOTE:
If assigning a key fob to a zone, the “ON/OFF” buttons on the key fob will no longer arm/disarm the system. The
key fob is converted to a “panic only” device.
Dealer Code
Press the
R
button directly enter the Dealer Code (default = 456789),
including leading zeros. Use the
1
through
9
buttons. NOTE:
Press the
0
button for a zero. Press
U
to save.
Re-enter the Dealer Code.
Press
U
to save. Press NEXT (
P
) button to proceed.
ZONE DESCRIPTIONS:
GEM-K4RF cannot be used to enter
Zone Descriptions. To enter Zone Descriptions you must
use the
GEM-K1CA Keypad or the Napco Quickloader Software.
DATA
ENTRY
AUX 1/AUX 2
OPTIONS
•
(blank)
None
1
Relay Group 1
2
Relay Group 2
9
Keypad Panic
0
Aux K.P. Panic
B
Instant
C
Toggle Aux
Relay
D
Access Control
EXIT DEALER PROGRAM MODE:
This completes the custom default program. Press the
C
button to enter the
Direct Address Program Mode for further programming or press the
C
button once again to end all programming
and resume normal keypad operation.
NOTE:
When programming the ID Code
number:
“A” =
G 0
; “B” =
G 1
;
“C” =
G 2
; “D” =
G 3
;
“E” =
G 4
; “F” =
G 5
.
Programming the GEM-P816 & GEM-P1632 (v.9A and Earlier)
KeyFob
# Area # 6-digit RF ID # Checksum # Aux1 #
R
R
(Direct Entry)
(Direct Entry)
CHIME
29
CHIME
0I
(Direct Entry)
CHIME
33
CHIME
4
CHIME
r
E
r
E
