10
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number
buttons
1
through
9
.
NOTE:
Press
G0
for a zero and
0
for a blank space (•). Press
G
1
through
G
4
for
letters B–E, respectively. Press
U
to save. Press NEXT (
P
) button to
proceed.
NOTE:
Central Station Receiver 2 and 3 Formats can only be entered in
Direct Address Programming. See CS Receiver Options.
Enter User Codes
For default program, enter up to 32 User Codes, with Area 1 and Area 2
Options. Press the (
R
) button once to set the cursor to the User Code.
Use the number buttons
0
through
9
to enter the User Number, followed
by
R
and a User Code of up to 6 digits. Enter
G0
for a blank.
NOTE:
If “Enable Global Ambush Code”(Address 0720) is enabled and
“Global Ambush Code” (Address 1054) is left blank(•),
do not
program the
first two digits of ANY User Code as '99'.
•
Press
U
to save. To proceed to the next User Code, press the
R
button to set the cursor to the User Number
and change it using the number buttons.
•
If the programmed code was less than 6 digits, enter blanks
G0
for the remaining digits.
Example:
Program a code of “2222” for user 02, with area 1 options of “Arm/Disarm” and “User Program”:
Enter
02
for the user number,
2222
G0
G0
for a user code,
G09
“(blank) 9” for area 1 options and
G0G0
“(blank) (blank)” for area 2 options.
CHANGING OR CANCELING A CODE:
To change any code, merely program over the existing code as described
above and press
U
to save. Similarly, to cancel a code, blank out each number of the code press
U
to save.
DATA
ENTRY
CS RECEIVER 1 FORMAT
•(blank) Ademco Slow, Silent Knight Slow
2
Radionics Fast
3
Silent Knight Fast
4
Radionics, CD, Franklin Slow
DATA
ENTRY
CS RECEIVER 1 FORMAT
5
Universal High Speed
B
SIA
C
Ademco Point ID
E
Pager
USER AREA OPTIONS - Select the desired Area Options (Area 1 and
OPTION ENABLED
L
R
EXPLANATION
blank(•)
blank(•)
Disabled
User Code not active in this area.
blank(•)
1
Arm/Disarm
Allows User Code to arm/disarm this area.
blank(•)
2
Arm Only
Prevents User Code from disarming this area.
blank(•)
3
Service
A Service Code has restricted arm/disarm rights; if an area is armed with a Service Code, the area can be disarmed
with any valid User Code, including a Service Code. If the area is armed with OTHER than a Service Code, it
CANNOT be disarmed with a Service Code.
blank(•)
4
Access
This is normally used to activate a door striker while an area is disarmed. Also program “Access Control on PGM2
Output” (Address 0719) and “PGM2 Output Access Control Timeout” (Address 0711).
blank(•)
Add 8
* User Program
User Program Option is enabled for Keypad 1 only, wherever it is connected (Area 1 or Area 2).
DATA ENTRIES
User # User Code Area 1 Area2
Options Options
R
Programming the GEM-P816 & GEM-P1632 (v.9A and Earlier)
NOTE:
When entering the Area 1
and Area 2 options, press
G0
for a ten. Enter
0
for a blank.
R
(Direct Entry)
(Direct Entry)
CHIME
26
CHIME
0
(Direct Entry)
(Direct Entry)
CHIME
27
CHIME
0I
