L
NAPCO Security Systems
Freedom F-64 Programming Instructions
Page 5
WI1502A 9/06
DEALER PROGRAM MODE
1. Press
456789 R
2. Press PRIOR/NO
button until
"
ACTIVATE PROGRAM Y/N
"
appears on LCD screen.
3. Press
NEXT/YES
button to Enter Dealer Program Mode.
4. Press
CC
to Exit Dealer Program Mode when finished.
•
Total Number of Zones in Area 1
•
Panel Zone Doubling
•
Fire Zones in Area 1
•
2-Wire Fire Zones in Area 1
•
Local or Central Station Reporting System
•
Exit/Entry Zones in Area 1
•
Interior Zones in Area 1
•
24 Hour Zones in Area 1
•
Chime Zones in Area 1
•
Chime 2 Zones in Area 1
•
Exit/Entry2 Zones in Area 1
•
50mS Loop Response Zones
(
Note:
750mS is
required for Loop Response time in UL installations)
•
Aux Output Activated on Alarm Zones
•
Sensor Watch Zones
•
Keypad Sounder On Alarm Zones
•
Auto Bypass Re-entry Zones
•
Enable No EOLR Zones
•
Enable Telco Line Fault Test
•
Enable Burg Output Chirp on Keyfob
•
Enable SIA CP-01 Features
•
Number of Keypads in Area 1
•
Central Station Receiver 1 Telephone Number
•
Central Station Receiver 1 Account Number
•
Central Station Receiver 1 Format
•
Enter User Codes
•
RF Transmitter Points
•
Keyfob Transmitters as Arm/Disarm & Control
Devices
•
Keyfob Transmitters as Zone Input Devices
•
Enter Zone Descriptions
•
Enter Date
•
Enter Time
•
Dealer Code
•
Test Timer
•
Clear Dealer Program
•
Cold Start
NEW PANELS:
The custom default program may be created for new panels only. Once the panel has been programmed by any
means, the number zones will be suppressed and cannot be changed. Should it be necessary to create a new custom default pro-
gram, (a) from the Dealer Program Mode, press the
C
button to enter the Direct Address Program Mode; (b) access Location
2285 (Clear Program); (c) press
U
and start over.
This procedure will automatically set up system keypads/Touchpads, EZMs, wireless transmitters, etc. After your basic default pro-
gram has been loaded, you may alter it as necessary in the Direct Address Program Mode.
ACCESSING DEALER PROGRAM MODE
CUSTOMIZING A DEFAULT PROGRAM
For new panels, you can design a default program that will best suit your application. Using this procedure, you will configure the panel for:
Default Dealer Code
DEALER PROGRAM - PRELIMINARY INFORMATION
Dealer Program Mode
comprises
two (2)
operational states:
1. EASY MENU DRIVEN PROGRAM MODE -
Used with new "out of the box" panels, this mode allows the dealer to customize the fac-
tory panel program to best suit the installation. The
Easy Menu-Driven Program Mode
is a menu-driven utility that prompts the in-
staller to configure the system (see page 6). Press
C
at any time to exit, thus entering
Direct Address Program Mode
, detailed
below.
2. DIRECT ADDRESS PROGRAM MODE -
Additional programming changes, if necessary, can be made in the
Direct Address Pro-
gram Mode
. In this mode, the programming address is accessed directly and re-configured by the installer.
The factory default Dealer Code is
4
5
6
7
8
9
. We recommend that you use this code to enter
Dealer Program Mode and program a custom Dealer Code, replacing the factory default Dealer Code. If you clear your
Dealer Code, use the Default Dealer Code once again to enter programming.
After entering codes or data, press the save
U
button. Data will not be stored into memory unless
U
is pressed.
If the programmer is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.
Silence the sounder by the
G
button to continue, or by pressing the
C
button to exit.
When programming a Multiple Area System, Direct Address Programming Mode must be used to complete the program.
DEA
L
ER P
R
O
G
R
A
M M
O
D
E
