Napa CARLYLE DTW12FL Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 30

Napa CARLYLE DTW12FL Скачать руководство пользователя страница 11

DTW38FL, DTW12FL

11

Rev. 01/23/13

PEAK HOLD MODE

1. Repeat steps 1 through 3 from "Viewing Peak Hold

Values". Then, using the buttons, navigate

to the location you wish to delete.

2. Press the button.

"No?" appears in the display.

3. Press the button again.

"dEL" appears in the display, and this action deletes

the current entry.

4. The preceding memory location and torque value will

now alternate on the display.

5. To exit press the button four (4) times.

Note: The display will automatically return to the

location that preceded the one deleted. For example,

If location 15 (n015) was deleted from memory,

the display would then show (n014) location 14.

When a stored value (location number) is removed from memory, the subsequent location numbers are reassigned. If

location 3 is deleted, the value that was in location 4 moves down one slot and becomes value 3. The value in location

5 moves to 4, etc.

Deleting a Peak Hold Value:

Deleting all Peak Hold Values:

1. Repeat steps 1 through 3 (Viewing Peak Hold Values").

2. Press the button; "cLrA" appears in the display.

3. Press the button; "no?" appears in the display,

4. Press the button; "dEL" appears in the display

followed quickly by "no-0" alternating with "0000".

5. Press the button; "ConU" appears in the display

6. Press the button again to return to the opening/

start display screen.

OPENING/START DISPLAY

«
...
9
10
11
12
13
...
»

Содержание CARLYLE DTW12FL































Отзывы:

Нет отзывов