NANOTEC PD4-E Скачать руководство пользователя страница 71

Страница: 71 / 295

Technical Manual PD4-E-M (EtherCAT)
6 Operating modes

Note

The target is absolute and, thus, independent of how often it was sent per cycle.

Note

The limit switches and, thus, the tolerance bands are active in this mode. For further information on
the limit switches, see Limitation of the range of motion.

Activation

To activate the mode, the value "8" must be set in object 6060

(Modes Of Operation) (see "CiA 402

Power State Machine").

Controlword

In this mode, the bits of controlword 6040

have no special function.

Statusword

The following bits in object 6041

(statusword) have a special function:

Bit

Value

Description

The controller is not in sync with the fieldbus

The controller is in sync with the fieldbus

Reserved

Controller does not follow the target; the preset of 607A

(Target Position) is

ignored

Controller follows the target; object 607A

(Target Position) is used as the

input for position control.

No following error

Following error

Bit 11: Limit exceeded: The demand position is above or below the limit values set in 607D

6.7.2 Object entries

The following objects are necessary for controlling this mode:

•

607A

(Target Position): This object must be written cyclically with the position set value.

•

607B

(Position Range Limit): This object contains the preset for an overrun or underrun of the

position specification.

•

607D

(Software Position Limit): This object defines the limitations within which the position

specification (607A

) must be located.

•

6065

(Following Error Window): This object specifies a tolerance corridor in both the positive and

negative direction from the set specification. If the actual position is outside of this corridor for longer
than the specified time (6066

), a following error is reported.

•

6066

(Following Error Time Out): This object specifies the time range in milliseconds. If the actual

position is outside of the position corridor (6065

) for longer than this time range, a following error is

triggered.

•

6085

(Quick-Stop Deceleration): This object contains the braking deceleration for the case that a

quick-stop is triggered.

Version: 1.0.1 / FIR-v1748

Содержание PD4-E








































































































































































































































































































Результаты поиска

Содержание PD4-E

Отзывы:

Похожие инструкции для PD4-E

Бренды по названию

Популярные бренды

NANOTEC PD4-E, Техническое руководство

Результаты поиска

Содержание PD4-E

Отзывы:

Похожие инструкции для PD4-E

Бренды по названию

Популярные бренды