![background image](http://html2.mh-extra.com/html/namco/quick-and-crash/quick-and-crash_operators-manual_3181241005.webp)
Page 5
REMOVING AND REPLACING PARTS
Adjustments or maintenance on this equipment should be carried out by suitably qualified
personnel only.
Do not make any alteration to this equipment without prior approval. Doing so could cause
unforeseeable danger.
Only parts specified by Namco Europe Ltd. should be used when replacing parts. (Including
screws)
Ensure that the power to the equipment is turned OFF before commencing any maintenance work.
(Trouble shooting, repairs etc.)
If performing work not described in this manual, contact your distributor for instructions, as no
responsibility will be accepted for damage or injury.
Parts of the Power Supply carry high voltage even after switching OFF and could cause burns or
electric shock. Take care not to touch these parts accidentally.
Make sure that the equipment is switched OFF before connecting or disconnecting any plugs or
connectors.
When moving the mains connector from the equipment, or the mains plug from the wall outlet,
always grasp the plug and not the cable.
MOVING THE EQUIPMENT
This equipment is fitted with castors to make it easier to move. Take care when moving the
equipment on an inclined surface.
The Header Assembly has a forward centre of gravity, so it is important that at least two people
are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is high, and it is important that a means of reaching
the height safely, without stretching, is available. (e.g. Steps, Step Stool etc.)
The overall height of the equipment , with the Header Assembly fitted, is 2050mm. Take care of
any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.
NOTES ON INSTALLATION
NEVER turn the power to the machine ON until installation has
been completed.
In order to prevent possible electric shocks, be sure that the
equipment is connected to the mains with a securely
connected earthed plug.
So that customers are not injured by the movement of the
equipment, ensure that there is at least 500mm seperation
between other equipment or walls.
In order to avoid damage to the equipment due to mis-operation,
ensure that the voltage of the mains supply is 230volts AC.
Note: If the location of this equipment has a polished floor, it is
recommended that rubber pads are fitted under the level adjusters
to prevent the equipment sliding on the floor when in use.
Note: In order to gain access to the Power Supply and CPU assemblies,
ensure that the rear of the equipment is seperated from a wall or
other equipment by at least 100cm
55cm
76cm
243cm
100cm
100cm
100cm
100cm
Maintenance Zone
Maintenance
zone
Play
zone
Maintenance
zone
Содержание Quick & Crash
