NAKTO Super Cruiser Скачать руководство пользователя | Manualshive

Страница: 21 / 29

background image

Step Nine：Inﬂate the tires.

Check that the tire beads and tires are evenly seated around the rims. Use

a pump with a Schrader valve and pressure gauge to inﬂate each tire to

the recommended pressure indicated on the tire sidewall. Do not overin-

ﬂate or underinﬂate tires.

Step Ten: Charge the battery.

Operate the electrical system when the battery has been adequately

charged and the battery is secured to the frame mount.

Your Nakto bike comes partially charged. We recommend you Connect

the charger input plug (110/220-volt plug) to the power outlet for 3 to 4

hours. The charger light will go from red to green when it is fully charged.

Step Eleven: Ensure all hardware is tightened properly

following recommended torque values.

Recommended Torque Values:

Hardware Loca

�

on

Hardware

Torque Required

(Nm)

Front Dropout Area

Front Axle Nuts

40

Handlebar Area

Handlebar Stem Clamp Bolts

10

Handlebar Area

Stem Bolts

10

«
...
19
20
21
22
23
...
»

Содержание Super Cruiser






























Отзывы:

Нет отзывов

Похожие инструкции для Super Cruiser

Universal Kids Bike

Бренд: Cosmic Страницы: 33

Бренд: VDO Страницы: 236

LEFTY SPEED DLR2

Бренд: Cannondale Страницы: 36

Бренд: Bell Страницы: 48

CITY EASY URBAN

Бренд: I-Bike Страницы: 76

Бренд: Rose electronics Страницы: 2

Бренд: kikkaride Страницы: 15

Бренд: Magura Страницы: 22

Бренд: Sepnine Страницы: 5

Бренд: Kidvelo Страницы: 6

Бренд: Electron Страницы: 32

Бренд: Kinderkraft Страницы: 24

Бренд: Kinderkraft Страницы: 24

Бренд: Frisco Страницы: 15

Бренд: Trikke Страницы: 30

ONE SECOND CLIP

Бренд: Decathlon Страницы: 2

Бренд: Decathlon Страницы: 5

Бренд: Decathlon Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды