manualshive.com logo in svg

Nakanishi NE330, Руководство по эксплуатации, Страница: 25 / 27

Поделиться
Скачать
Nakanishi NE330 Скачать руководство пользователя страница 25

48

Specifications

9 – 3 

Protection Circuitry

 

Š

Protection Features

࣭

When output power of 20W or more in CLAMP mode or 45W or more in UNCLAMP mode is 
detected, the unit will stop operating for safety. (see "7

̴

–

̴

1 Error code"03") 

࣭

If the handpiece is pulled out of the connector during operation, it will stop.

࣭

To prevent the handpiece from forgetting to turn it off, the handpiece will stop automatically if it is still 
unused when it is on. (see "7

̴

–

̴

1 Error code"13") (Time to stop can be changed by user settings. It 

can also be disabled. see "6

̴

–

̴

2 Setting the forced stop time when not in use")

 

CAUTION

 

Ɣ

If the main power switch is turned on while stepping on the foot switch, it will be disabled for safety reasons. 
Release the foot switch because the indicator on the operation panel blinks and a notification sounds. The drive 
prohibit state is lifted and the unit can be used normally.

 

Ɣ

The handpiece temperature rise is predicted from the output power and if the tool is found to be generating 
excessive heat, the handpiece heat protection function is activated, the display on the control panel flashes and 
an audible alarm sounds.  
After that, it automatically suppresses the output and keeps the temperature from rising, allowing for continuous 
use. When the temperature drops, the indicator on the control panel blinks and the notification sound is 
automatically cancelled.  
(You can also disable it through user settings. 6 – 6 Setting the handpiece heat protection function")

 

Š

How to clear the error condition with the protection function

If the protection function is activated and the error is stopped, remove the cause of the activation of the 
protection circuitry and then clear the error state by performing the following operations
Press the ON / OFF key or step on the foot switch again. The ERROR LED goes off and the error 
state can be cleared.

9 – 4 

Symbol

Note, see Operating Instructions

Conforms to European Directives

Conforms to North American Safety Standards (UL, CSA)

Disposal of products and accessories in accordance with the EU Directive 
on Waste Electrical and Electronic Equipment (WEEE) (2012/19/EU)

serial number

Caution, high temperature surface

B6KHHQXV=(52B(1BLQGG

Содержание NE330




























Отзывы:

Нет отзывов