manualshive.com logo in svg

Nakanishi HES810, Руководство по эксплуатации

Поделиться
Скачать
Nakanishi HES810 Скачать руководство пользователя страница 11

30

①

Set the provided 8mm wrench on the spindle shaft.

②

Place the provided 11mm wrench on the collet nut and turn it counterclockwise to loosen the 
collet and remove the tool (The first turn will loosen the collet nut, but the tool will not release and 
turning will become stiff. Keep turning through the stiffness and the collet will open).

③

Clean the collet and collet nut, then insert the new tool and tighten the collet by turning clockwise. 
Do not over-tighten.

9

11

5

8

Loosen

Tighten

Tool

Spindle Shaft

Collet Nut

Fig. 10

CHANGING THE TOOL

7.

Do not tighten the collet without inserting a tool or dummy bur, as this will damage the 

collet, spindle or collet nut, causing difficulty removing the collet.

   CAUTION

Please set the cutting tools to minimize the overhang amount. 13mm is the maximum 

amount of overhang to maintain high accuracy and safety. 

 RECOMMENDATION

OM-K0587 002_HES810_(A5x18)_EN_150205.indd   30

2015/02/05   17:24:47

Содержание HES810























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды