Nailor 92FFD Скачать руководство пользователя

Страница: 16 / 24

NETWORKING

When networking the fan filter units whether in a local area network (LAN) or connecting to a BAS / BMS system, each unit is

connected in a straight-through daisy-chain using Cat5e or Cat6 network cables and the on-board RJ45 connectors.
If field cutting network cables, it is important for each end of the cable to be wired identically. However, assembled network

cable are available; field assembled cables are the leading cause of problems in new systems.

WHAT TO EXPECT:

One unit will be clearly labelled MASTER UNIT. This unit will contain the ACC1001-25 and power supply. The power supply

can be left in the master unit control box and control board can be mounted anywhere in the space, including at the master

unit.

Page 16 of 24

9/18 IOM-FFDINST

Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation.

UNIT CONTROL BOARD WITH MODBUS CAPABILITY

POWER SUPPLY BOARD

CAN BE LOCATED IN THE

FAN FILTER UNIT OR IN

THE CONTROLS ENCLOSURE.

ACC1001 CONTROL USED AS AN EXAMPLE.

OTHER CONTROLLER OPTIONS ARE AVAILABLE.

Содержание 92FFD

























Результаты поиска

Содержание 92FFD

Отзывы:

Похожие инструкции для 92FFD

Бренды по названию

Популярные бренды

Nailor 92FFD, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание 92FFD

Отзывы:

Похожие инструкции для 92FFD

Бренды по названию

Популярные бренды