Nagel 2S Trimmer страница 4 Скачать руководство пользователя

Страница: 4 / 30

1. Safety

The 2-Side Trimmer may only be plugged in to an approved and by circuit breakers

protected electrical installation, which is secured with a maximum of 16A.

The outlet socket shall be installed near the equipment and shall be easily accessible.

Never put your hands, other body parts or anything else then booklets within trimming

specifications in the infeed or outfeed of the 2-Side Trimmer.

Before cleaning, maintenance or repairs always be sure to switch off the power switch and

disconnect the appropriate power cord.

Always follow all warnings marked on or supplied with the equipment.

The equipment should only be placed on a solid surface with adequate strength to hold the

extra weight of the machine besides the usual maximum load.

Always exercise care while moving or relocating the equipment.

Keep magnets and all devices with a strong magnetic field away from the machine.

Never attempt to perform maintenance or repairs other than described in this manual.

Never remove covers or guards that are fastened with screws.

Never install the equipment near a radiator or any other heat source.

Never override or bypass electrical or mechanical interlock devices.

In case of unusual sounds or noises, abnormal surface temperature or odours disconnect the

equipments power source immediately and consult a qualified technician.

The manufacturer cannot be held responsible for arbitrary changes in the machine and the

originated

damage.

Make sure that the 2-Side Trimmer is NOT powered during installation or service activities.

This is a Class A product. In a domestic environment this machine may cause radio

interference. In which case the user may be required to take adequate measures.

Note:

A domestic environment is an environment in which a radio and television receivers

can be expected inside a range of 10 meters of the concerning machines.

RoHS

compliant

The 2-Side Trimmer is RoHS compliant.
ONLY use RoHS compliant replacement parts ordered from NAGEL.

Содержание 2S Trimmer































Результаты поиска

Содержание 2S Trimmer

Отзывы:

Похожие инструкции для 2S Trimmer

Бренды по названию

Популярные бренды

Nagel 2S Trimmer, Руководство пользователя

Результаты поиска

Содержание 2S Trimmer

Отзывы:

Похожие инструкции для 2S Trimmer

Бренды по названию

Популярные бренды