6 VACUUM FLUORESCENT DISPLAY (VFD)
•
Displays visual information about the current settings like the active
Source, volume level, listening mode, audio format, applicable
RDS/XM/DAB as well as iPod-related display information and other
related indicators.
•
Refer also to the item about DISPLAY SETUP under the USING THE
T 787 - SETUP MENU segment of the OPERATION section.
7 REMOTE SENSOR
•
Point the HTR 8 remote control at the remote sensor and press the
buttons.
•
Do not expose the remote sensor of the T 787 to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the T 787 with the remote control.
Distance:
About 23ft (7m) from the front of the remote sensor.
Angle:
About 30
o
in each direction of the front of the remote sensor.
8
a
SOURCE
s
•
Toggle through the input selections - Source 1, Source 2, Source 3,
Source 4, iPod, Source 7, Front Input, Media Player and Tuner (AM/
FM/DAB/XM as applicable). More Sources can be directly recalled
upon enabling them at the Setup Menu.
•
Refer also to the item about SOURCE SETUP under the USING THE
T 787 - SETUP MENU segment of the OPERATION section.
9 VOLUME
•
The VOLUME control adjusts the overall loudness of the signal being
fed to the loudspeakers or headphones.
•
Turn clockwise to increase the volume level; counter clockwise to
lower it.
10 PHONES
•
Accepts stereo headphone using a standard 1/4-inch stereo phone
plug (use a suitable adaptor for headphones equipped with a
smaller plug).
•
For headphone listening, the Front speakers must be set to “Large” at
the “Speaker Configuration” of the Speaker Setup item at the Setup
Menu; otherwise headphone bass response will be restricted.
11 A SPEAKERS B
•
Press either Speaker A or B or both to select the set of speakers you
wish to listen.
•
Speaker A is the main set of 7 multichannel and surround speakers.
•
Speaker B is an auxiliary set for remote locations such as other
rooms of your home. For Speaker B selection, all surround sound
sources are downmixed to stereo. Combining Speaker A and
Speaker B (SPEAKERS A + B) will also result to the source being
downmixed to stereo.
12 AM/FM/DB
•
Toggle this button to select AM, FM, DAB (230V version only) or XM
(120V version only) tuner functions.
13 TUNER MODE
•
In FM mode, this button will toggle between FM STEREO and FM
MONO.
•
Select FM MONO (FM STEREO and FM MUTE icons at VFD are
extinguished) for stations that have too much interference or are
too weak.
•
In DAB (230V version only) or XM (120V version only) radio, this
button enables the digital radio menu in conjunction with the
Navigation and Enter buttons.
14 LISTEN MODE
•
Toggle to select through the various Listening mode options.
Depending on the format of the currently selected input (digital
or analog, stereo or multichannel), various listening modes are
available.
•
Refer also to the item about LISTENING MODE under the USING THE
T 787 – MAIN MENU segment of the OPERATION section.
15 TONE
•
Press to adjust TREBLE control using the VOLUME knob over a
± 10dB range. Press again to adjust BASS control and a third time for
DIALOG control.
•
Refer also to the item about TONE CONTROLS under the USING THE
T 787 – MAIN MENU segment of the OPERATION section.
16 TONE DEFEAT
•
Tone Controls are enabled or disabled by pressing this button. Tone
controls are bypassed at “Tone Defeat” while at “Tone Active”, the
tone controls are enabled again.
•
Refer also to the item about TONE CONTROLS under the USING THE
T 787 – MAIN MENU segment of the OPERATION section.
17 FRONT INPUT/MP
•
Toggle button to switch between Front Input and Media Player
input.
18 FRONT INPUT PORTS
•
Use these convenience jacks for occasional sources such as a
camcorder, video game console, any analog audio or HDMI sources
and composite or S-Video sources.
•
If your source has a single audio out jack only or is marked “Mono
output”, plug this into the T 787’s Front “R (MONO)” input (item B).
•
On the other hand, if your source has two output jacks indicative of
stereo output, insert both jacks into the T 787’s corresponding Front
“L” (item A) and “R (MONO)” input to achieve stereo output as well.
•
Connect composite video output source to the front composite
video input (item C).
•
Connect S-Video output source to the front S-Video input (item D).
•
Use the front HDMI input (item E) to connect directly an HDMI
output source.
19 FRONT MP/MIC INPUT
•
Connect your Media Player’s standard stereo phone jack to this
input.
•
This is also same input where the supplied Audyssey microphone is
connected for Audyssey Auto calibration.
•
Refer also to the item about AUDYSSEY AUTO CALIBRATION under
the USING THE T 787 - SETUP MENU segment of the OPERATION
section.
IDENTIFICATION OF CONTROLS
FRONT PANEL
7
ENGLISH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ
