NAD T 778, Руководство пользователя, Страница: 31 / 36

ENGLISH
31
Example: Record a Macro to the [0] key to turn ON the T 778, turn ON
the DVD Player, Select Input 1 (Source 1) and commence disc playback of
connected Source 1 device (as in the DVD player)
•
On the HTR 8, simultaneously press-and-hold [MACRO] and [0]
(numeric zero); the Learn LED turns steady green.
•
Press [AMP], press [ON]; press [DVD], press [ON]; press [AMP], press [1]
(Input 1); press [DVD], press [
4 ] (Play) – the Learn LED blinks as each
step is added.
· Press [MACRO] again to exit the macro-record mode.
To clear a macro, perform the above steps without entering any functions.
EXECUTING MACROS
To execute a macro, press and release [MACRO]; its key illumination lights
for 5 seconds. While it remains lit, press an HTR 8 key to which a macro has
previously been stored.
The corresponding macro will run; as each step executes, its “parent”
DEVICE SELECTOR key flashes briefly; when execution is finished, the
[MACRO] key illumination goes out. Pressing any other HTR 8 key while a
macro is executing will abort the macro. Remember that you must hold the
HTR 8 so that its infrared emitter can activate the target components.
NOTE
When a macro executes, a 1 second delay is automatically inserted
between its commands. If you need more than a 1 second delay
between particular commands—for example, to permit a component to
power up completely—you can record “empty” steps into the macro by
changing DEVICE SELECTOR “pages” without entering actual command
functions.
KEY ILLUMINATION TIMEOUT
The HTR 8’s key-illumination can be set to remain lit for 0-9 seconds. The
default value is 2 seconds. To set the illumination timeout, simultaneously
press-and-hold for 3 seconds both the HTR 8’s [DISP] and the [0-9] key, with
the digit corresponding to the desired timeout duration; the Learn LED will
flash twice to confirm the new setting. When set to zero, the illumination
will not turn on at all.
NOTES
· Key illumination is activated when one presses any HTR 8 key.
· If HTR 8 senses movement, key illumination is activated without having
to press a key. If HTR 8 is shaken, key illumination is also activated.
· Key illumination is the biggest drain on the HTR 8’s batteries. A short key
illumination timeout will extend battery life appreciably; turning it off
altogether (set it to 0 seconds) will lengthen it still further.
CONFIGURING KEY ILLUMINATION
Keys to Press
(for 3 seconds)
Mode
DISP + Digit Key (0-9) Set key illumination timeout to number of seconds
corresponding to digit key. Zero turns off the key
illumination entirely.
DISP + OFF Disable light sensor. Key illumination will turn on with any
key press.
DISP + ON Enable light sensor.
DISP + ENTER Set the light sensor threshold to the current light level.
DISP + RTN Restore all key illumination settings to the defaults.
FACTORY RESET
The HTR 8 can be reset to its factory state, deleting all learned commands,
copied and punched-through keys, macros, and other setup information;
reverting all keys to their pre-programmed library commands.
To perform a factory reset simultaneously press-and-hold for 10 seconds
the HTR 8’s [ON] and [RTN] keys; the Learn LED will start to flash green.
Release [ON] and [RTN] before the second flash is complete; the Learn LED
will turn red, indicating the remote has been reset.
NOTE
You must release [ON] and [RTN] before the second flash goes out,
otherwise the unit will not reset; should this occur, repeat the full
procedure.
DELETE MODE
The HTR 8 can store learned, copied, and “default library” commands on any
single key. The default library commands are the pre-programmed NAD
codes, such as the native T 778 commands on the [AMP] “page”.
You can delete commands by layers back “down” to the default library
command on any key, removing learned commands, punched-through
functions, and copied keys.
NOTE
The default library commands cannot be deleted, so you need not worry
that using Delete Mode might cause irreparable changes.
To enter Delete Mode, simultaneously press-and-hold for 3 seconds both
the desired key’s DEVICE SELECTOR key and the [RTN] key, until the Learn
LED turns green. Press the function key whose command you wish to
delete; the Learn LED flashes; the number of times indicates which type of
function has become active - see the table below. Press the active DEVICE
SELECTOR key again to exit Delete Mode.
NOTE
You may delete multiple function-key commands on the same DEVICE
SELECTOR “page”, but to delete from more than one DEVICE SELECTOR
page you must exit Delete Mode and then re-enter it on the required
page.
Flashes Command Type
1 Default Library Command
2 Copied Library Command
3 Learned Command
OPERATION
USING THE HTR 8 REMOTE CONTROL