Nabco U30 Скачать руководство пользователя

Страница: 7 / 27

Getting Started

2-6

U30 Microprocessor Control

www.NabcoEntrances.com

Part #15-9000-30

Rev. 3-12-13

Table 2-2

U30 Microprocessor Control Specifications

Specification

Description

Recommended Temperature Range

-4° to 140°F (-20° to +60° C)

Maximum recommended door weight

600 pounds total

(300 pounds each for a bi-part or 600 pounds for a single)

Hold Open time delay

0 to 67 seconds

Door Movement range

4 to 137 inches (100 to 3500 millimeters)

Door Movement range for Limited Door

Opening Feature

4 to 137 inches (100 to 3500 millimeters)

Back Check range

2 to 5 inches (50.8 to 127 millimeters)

Function

LED

LED Display

Power

Red

(LED will blink when an error occurs)

61 (Activation)

Green

6B (Holding Beam)

Green

H (Reduced Opening)

Green

62 (Activation)

Green

BA (Panic Breakout and OFF)

Green

ERROR

Red

Table 2-3

U30 Microprocessor Control Software Specifications

Program

Description

History Data

Maintains data under the History Data program

Maintenance Count

Counts number of times Handy Terminal has been connected for service and tracking.

Operation Count

Counts number of full door operations

(Operation counts are registered in increments of 100 per power-on period)

Recycle Count

Counts number of times the slide door has recycled.

Содержание U30




























Результаты поиска

Содержание U30

Отзывы:

Похожие инструкции для U30

Бренды по названию

Популярные бренды

Nabco U30, Полное руководство по установке и программированию

Результаты поиска

Содержание U30

Отзывы:

Похожие инструкции для U30

Бренды по названию

Популярные бренды