Nabco Opus Control Скачать руководство пользователя страница 33

Страница: 33 / 35

33 of 35

www.NabcoEntrances.com

OpusControlWiringandProgrammingInstallationManual

Rev. 3-9-18

P/N C-00139

Programming Tips

Tip

Action

To copy settings from one

Sim Pair Control to the other

Sim Pair Control

►

Software Revision (up to 19)

• On the Control being programmed, after other settings are complete, go to “SimPair Setting”

under “Optional Settings”. Change to “Single Door” then back to “Normal Sim Pair” (or

“Overlap Sim Pair”). Then, when moving back out of the programming, before reaching the

main status screen, a prompt will come up to “Copy Settings” “Yes No”. Select “Yes”.

►

Software Revision (20 and up)

• The “copy Settings” prompt will always appear when backing out ofprogramming if the

control is set to Sim Pair, without the need to select Single first.

Error Messages

Error Msg

Description

Resolution

Recycle Warning

Recycle was detected more than (5) times while

opening or closing cycle continuously.

►

Check Door resistance and Door Path for

resistance to movement.

• It may be necessary to adjust the Recycle

Sensitivity.

MPU

Microprocessor detects errors within the Internal or

External Circuits.

►

This could be a random error.

• If the Error occurs repeatedly, please replace

the Opus Control.

Drive Circuit

If the Drive Circuit detects an unusual state, the

Opus will stop door movement. Possible causes are:

►

Abnormal voltage at Motor Circuit

►

Abnormal current draw from motor.

►

Check all connections between the Control

and Motor.

►

Check Motor Fuse

►

Check motor for open circuit, short circut, or

short to ground.

►

It is possible electrical noise may cause

a false error. If the error does not occur

repeatedly then it’s most likely not an issue.

Communication

►

CAN-bus Communication Error

►

Can happen in Simultaneous Pair applications.

Check the CAN-bus Cable between the two Opus

Controls.

61 Sensor

►

Incorrect sensor wiring related to that input.

Incorrect settings on sensor and/or control

related to sensor monitoring.

►

Sensor has failed.

►

Check sensor wiring.

►

Check settings on sensor and/or control

related to sensor monitoring.

►

Try a new sensor.

62 Sensor
6B Sensor
SWL Sensor

Notice: If after troubleshooting a problem, and a satisfactory solution cannot be achieved, please call

Nabco Entrances at 1-877-622-2694 between 8 am – 4:30pm Central time for additional assistance.

DO NOT leave any problem unresolved. If the door cannot be repaired immediately, turn off the

door and leave it inoperable until repairs can be made. Advise the owner NOT to operate the door

in the automatic mode until repairs are effected. NEVER leave a door operating without all safety

detection systems operational.

Содержание Opus Control




































Результаты поиска

Содержание Opus Control

Отзывы:

Похожие инструкции для Opus Control

Бренды по названию

Популярные бренды

Nabco Opus Control, Руководство по установке

Результаты поиска

Содержание Opus Control

Отзывы:

Похожие инструкции для Opus Control

Бренды по названию

Популярные бренды