background image

(Revised 2014-01-23) 

WARNING: 

Do  not  operate  the  unit  with  the  end  plates  removed,  as  this  could  create  a  shock  or  fire 

hazard. 

ALERTE : 

Ne  pas  faire  fonctionner  l'unité  avec  les  plaques  d'extrémité  retiré,  ce  qui  pourrait  créer  une 

décharge électrique ou un incendie. 

 
WARNING:

 Properly ground the unit before connecting anything else to the unit.  Units not properly grounded 

may result in a safety risk and could be hazardous and may void the warranty.  See the grounding technique 
section of this user manual for proper ways to ground the unit. 

ALERTE:

 Correctement à la terre de l'unité avant tout raccordement à l'unité. Unités pas correctement mise à 

la terre peut entraîner un risque de sécurité et pourraient être dangereux et peut annuler la garantie. Voir la 
section technique de mise à la terre de ce mode d'emploi des moyens appropriés à la masse de l'appareil. 
 

WARNING: 

Do not operate the equipment in a manner not specified by this manual. 

ALERTE:

 Ne pas faire fonctionner l'équipement d'une manière non spécifiée par ce manuel. 

 

WARNING: 

Do not work on equipment or cables during periods of lightning activity. 

ALERTE:

 Ne pas travailler sur le matériel ou les câbles pendant les périodes d'activité de la foudre. 

 

WARNING:

 Observe proper DC Voltage polarity when installing power input cables.  Reversing voltage 

polarity can cause permanent damage to the unit and voids the warranty. 

ALERTE:

 Respecter la polarité correcte de tension DC lors de l'installation des câbles d'alimentation d'entrée. 

Inversion de polarité de tension peut causer des dommages permanents à l'appareil et annule la garantie. 
 

WARNING:

  Install only in accordance with Local and National Codes of authorities having jurisdiction. 

ALERTE:

 Installer uniquement, conformément aux codes locaux et nationaux des autorités ayant compétence. 

 

WARNING (1005TX only): 

This equipment is open-type device and is meant to be installed in an 

enclosure suitable for the environment that is only accessible with the use of a tool. 

ALERTE (1005TX uniquement):

 Cet équipement est ouvert de type périphérique et est destiné à être 

installé dans un boîtier adapté à l'environnement qui n'est accessible qu'avec l'utilisation d'un outil. 

 
LASER SAFETY 

(1002MC and 1003GX2 Models)

 

 

  

CAUTION:

 CLASS 1 LASER PRODUCT. Do not stare into the laser. 

 

 

ATTENTION:

 PRODUIT LASER CLASSE 1.  Ne pas regarder dans le laser. 

 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание 1002MC-LX-YY





















Отзывы: