N.KO UZ 12 Ultralight Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 35

N.KO UZ 12 Ultralight Скачать руководство пользователя страница 12

12

4.2

Setting Up and Connecting

Important:

The activities described in this section must be performed by qualified personnel only.

If the machine is used for machining of small workpieces, it must be fitted on a flat surface

(e.g. a workbench) using the opening in the bottom part of the stand (position A, fig. 4.2.1.).

Fig. 4.2.1.

If the machine is used for machining of large workpieces, it must be placed on the actual

workpiece and it must travel along the workpiece by itself during the work. The workers must

put the machine on the material and at the end of the process, they must take it off again. It is

advisable that the machine is suspended on the crane using a strap, as shown in fig. 4.1.1, at
least during approaching the material and at the end, when the material leaves the workpiece.

Caution:

If the machine is not adjusted correctly, the tool will not be sharp enough or the

machine will not be in a good condition. If inappropriate material to be machined is

selected, fall of the machine off the workpiece may occur.

While performing electrical connection, proceed as follows:

•

check frequency and voltage values on the engine rating plate,

•

attach the end of the cable to the mains using a plug according to your local electric

distribution system.

«
...
10
11
12
13
14
...
»

Содержание UZ 12 Ultralight




































Отзывы:

Нет отзывов