MyGate Q71A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 26

MyGate Q71A Скачать руководство пользователя страница 12

The MyGate Q71A Control Board Installation Manual : Printed 06/11/2012 14:18

12

Connecting power to the control board

Connecting power to the control board using 1.5mm - 3 core armoured cable 230v.

Cable identification should be:

Colour

Identification

Brown

Live

Blue

Neutral

Yellow / Green

Earth

Insert the Live (brown) wire to terminal 2 and the Neutral (blue) to terminal 3 and tighten the terminal
screws to ensure good safe contact is made. Please connect your Earth (yellow/green) wire to terminal 1.

Please switch the power supply on. After a few seconds you

will see three LED’s lit:

  DL3 (above terminal 15)
  DL4 (above terminal 16)
  DL5 (above terminal 18)

DL3 Lit =

Photocells status OK, wiring is complete and control board can see the photocells

DL4 Lit =

2nd set of photocells status is OK, wiring is complete and control board can see the photocells.

If second set of additional photocells are fitted (optional).

If a second set is not used, link must be placed between terminals 16 + 17.

DL5 Lit =

Emergency stop button status OK, wiring is complete and control board can see it.

If an emergency stop button is not fitted, a link must be placed between terminals 18 + 21

Now we look to program the remote control key-fob(s) to the control board.

«
...
10
11
12
13
14
...
»

Содержание Q71A



























Отзывы:

Нет отзывов