MyGate Q71A Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

MyGate Q71A Скачать руководство пользователя страница 10

The MyGate Q71A Control Board Installation Manual : Printed 06/11/2012 14:18

10

To Use in Closing Cycle

To connect power to Transmitter Unit

Use 1 core wire to connect AC+ on photocell
Transmitter Unit (TX) to Terminal 12.

Use 1 core wire to connect AC- on photocell
Transmitter Unit (TX) to Terminal 13

To connect power to Receiver Unit

Use 1 core wire to connect AC+ on photocell
Receiver Unit (RX) to Terminal 12

Use 1 core wire to connect AC- on photocell
Receiver Unit (RX) to Terminal 13

To connect the relay function to Control Board

Use 1 core wire to connect 3

rd

terminal (looking

from left to right) on photocell Receiver Unit (RX)
to Terminal 15

Use 1 core wire to connect 4th terminal (looking
from left to right) on photocell Receiver Unit (RX)
to Terminal 14

IMPORTANT: Please place a link between terminals 16 and 17

To Use in Opening Cycle

To connect power to Transmitter Unit

Use 1 core wire to connect AC+ on photocell
Transmitter Unit (TX) to Terminal 12

Use 1 core wire to connect AC- on photocell
Transmitter Unit (TX) to Terminal 13

To connect power to Receiver Unit

Use 1 core wire to connect AC+ on photocell
Receiver Unit (RX) to Terminal 12

Use 1 core wire to connect AC- on photocell
Receiver Unit (RX) to Terminal 13

To connect the relay function to Control Board

Use 1 core wire to connect 3

rd

terminal (looking

from left to right) on photocell Receiver Unit (RX)
to Terminal 17

Use 1 core wire to connect 4th terminal (looking
from left to right) on photocell Receiver Unit (RX)
to Terminal 16

IMPORTANT: Please place a link between terminals 14 and 15

«
...
8
9
10
11
12
...
»

Содержание Q71A



























Отзывы:

Нет отзывов