background image

Marleton Cross Limited Trading as The MX Group,

 Alpha Close, Delta Drive,Tewkesbury Industrial Estate,Tewkesbury, Glos. GL20 8JF.

www.mx-group.com email: [email protected]

Customer Care: 0845 505 2211

6752B_10_14_GF

MX GROUP GUARANTEE SERVICE POLICY 

In the event of you needing to contact the MX Group Customer Care Department, the following 

procedure should be followed:

1.  

 Before telephoning on 0845 505 2211 the MX Group Customer Care Department  you 

should ensure you have the model number (printed on the valve) and date and proof of 

purchase your contact details and the postcode where the unit is installed.

2.  

The MX Group Customer Care Department will be able to tell you whether the fault can 

be simply rectified by the provision of a replacement part or arrange an on site visit by a 

Qualified Service Engineer.

3.  

If a service call is required it will be booked and the date of the call confirmed. You or a 

representative (over the age of 18 years) must be present during the entire engineers 

visit. The engineer will not be able to repair or replace or advise on parts or products not 

supplied as part of the product.

4.  

A charge will be made in the event of a service call aborted by you, but not by  us, or  

where a call under the terms of guarantee has been booked and failure is not related  to 

product supplied by MX Group (i.e Scaling and furring, incorrect water pressure, or  other 

plumbing problem unrelated to the normal function of the products).

5.  

If the product is no longer covered by the guarantee, a charge will be made for the site 

visit and for any parts supplied.

6.  

Service charges are based on the account being settled when the work is complete. 

The engineer will request payment. If this is not made on the day or settled within ten  

working days, and administration charge will be added.

SPARE PARTS

In the event that parts or maintenance is needed outside the guarantee MX will endeavour to help 

with this. Spare parts codes are given in the fitting instructions. By calling the Customer Care 

Department on 0845 505 2211 with the part number, they will be able to quote you to supply 

these parts, usually via our spare parts distributor. 

MX Atmos Select 6752B 09_14_GF.indd   16

24/10/2014   14:57

Содержание Atmos Select Round

















Отзывы: