MVP INV-PAT-7-BPO Скачать руководство пользователя страница 19

Страница: 19 / 27

Patriot Innovator 2 BPO Unit Operations Manual

Page | 19

Innovator II Control Panel

Control Name

Type of Control

Function

Flush Button

Push Button

Press this button to operate the flush cycle

Mold Pressure
Guard

Preset Level Gauge

Displays signal air pressure being supplied to the Mold Pressure
Guard (MPG) control.

Mold Pressure
Guard

Regulator

Use this to adjust the MPG control signal air pressure.

Inject Button

Push Button

Press this button to start the machine in inject mode.

Recirculate
Button

Push Button

Press this button to start the machine in recirculation mode.

Stop Button

Push Button

Press this button to stop the machine in injection, recirculation, or
flush mode.

Stroke Count

Counter

Displays the current number of strokes the pump has performed.

Stroke Count
Preset Count

Counter

Displays the number of strokes at which the unit will shut down
when reached.

Stroke Count
Digit Modifiers

Spin Buttons

Click up or down to adjust the number in the Preset Count column
to set the stroke count the machine should stop at.

Digit Lockout

Button

Press this button to keep the stroke count setting.

Reset Button

Push Button

Press this button to reset the current stroke count.

Getting Started

1. Unpack unit.
2. Attach pickup hoses to the inlet of the pump.
3. Connect the yellow outlet tube from the outlet side of the solvent pump through the outlet

fitting to the flush neck on the flush valve of the injection gun.

4. Connect the ¼ inch pump inlet air tube to the other side of the SP4 pump inside the flush

tank.

RESET BUTTON

CURRENT COUNT DISPLAY

PRESET COUNT DISPLAY

DIGIT LOCKOUT

DIGIT MODIFIERS

Figure 2. Stroke Counter

Содержание INV-PAT-7-BPO




























Результаты поиска

Содержание INV-PAT-7-BPO

Отзывы:

Похожие инструкции для INV-PAT-7-BPO

Бренды по названию

Популярные бренды

MVP INV-PAT-7-BPO, Руководство по эксплуатации

Результаты поиска

Содержание INV-PAT-7-BPO

Отзывы:

Похожие инструкции для INV-PAT-7-BPO

Бренды по названию

Популярные бренды