MV Agusta F4 BRUTALE Скачать руководство пользователя страница 85

Страница: 85 / 179

- 83 -

ADJUSTMENTS

5.2. Table of adjustments

F - Front suspension adjustment: The fol-
lowing can be adjusted to adapt the response of
the suspension to the rider’s preference:

- spring preload (§5.6.1.)
- rebound damper (§5.6.2.)
- compression damper (§5.6.3.)

G - Rear suspension adjustment: The following
can be adjusted to adapt the response of the
suspension to the rider’s preference:

- spring preload
- geometry height

- rebound damper (§5.7.1.)
- high speed compression damper (§5.7.2.)
- low speed compression damper (§5.7.3.)

H - Drive chain adjustment: To ensure safe and
effective transmission of power.

L - Headlight adjustment: To adjust the range of
the light beam to the geometry of the motorcycle
(§5.8).

A - Front brake lever adjustment: Optimizes
the grip to suit the rider’s needs (§5.3).

B - Clutch lever adjustment: Optimizes the grip
to suit the rider’s needs (§5.4).

C - Gear lever adjustment: Optimizes the posi-
tion of the lever to suit the rider’s needs.

D - Rear brake lever adjustment: Optimizes the
position of the lever to suit the rider’s needs.

E - Rearview mirror adjustment: Optimizes the
orientation of the rearview mirrors (§5.5).

WARNING
Do not operate the screw fixing the rear-
view mirror to the handlebar. If this
screw needs to be tightened, contact
your MV Agusta dealer.

Содержание F4 BRUTALE




















































































































































































Результаты поиска

Содержание F4 BRUTALE

Отзывы:

Бренды по названию

Популярные бренды

MV Agusta F4 BRUTALE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание F4 BRUTALE

Отзывы:

Бренды по названию

Популярные бренды