MUTRADE Hydro-Park 1123 Скачать руководство пользователя страница 46

Страница: 46 / 52

Hydro-Park 1127 & 1123

USER MANUAL

MUTRADE INDUSTRIAL CORP.

Pressure cannot

be maintained

after platform

lifted up

Cylinder

retracts slowly

when

depressurizing

Cylinder does

not retract at all

when

depressurizing

Working noise

is too loud, or

abnormal noise

Motor does not

work

Valve element of one-way valve is blocked

One-way valve to be cleaned or replaced

Valve element of solenoid valve is blocked

Hydraulic oil deteriorates or is dirty

Throttle valve is blocked

Clean throttle valve and valve element

Throttle valve is not properly adjusted

Throttle valve to be re-adjusted

Valve element of solenoid valve is blocked

Solenoid valve to be cleaned or replaced

Valve element of solenoid valve is blocked

Solenoid valve to be cleaned or replaced

Coil of solenoid valve is broken, or

working voltage is too low

Replace coil of solenoid valve, or supply

normal working voltage

Motor is broken

Motor to be replaced

Hydraulic oil to be replenished into oil tank

Solenoid valve to be cleaned or replaced

Inlet ﬁlter is blocked

Replace coupling and clean inlet ﬁlter

Gear pump is broken

Gear pump to replaced

Hydraulic oil deteriorates or is dirty

Pressure relief valve is broken

Pressure relief valve to be replaced

Voltage shortage due to low supply voltage

Voltage stabilizer to be added

Voltage shortage due to too long

power line

Power line to be shortened, and

voltage stabilizer to be added

Voltage shortage due to too thin power

line

Thicker power line to be used, and

voltage stabilizer added

Starting capacitor is broken

Starting capacitor to be

replaced

Fitting of outlet pipe is not fastened or

sealing is broken

Fasten ﬁtting of outlet pipe, or replace

sealing
Replace hydraulic oil, clean inlet ﬁlter and

oil tank

Air is absorbed into gear pump due to lack

of hydraulic oil in oil tank

Pressure relief valve is turned on to make

hydraulic oil go back to oil tank due to over

Only cars within rated capacity can be parked

on platform. Or turn up setting pressure of

pressure relief valve (with permission by

Mutrade)

Replace hydraulic oil, clean inlet ﬁlter and

oil tank

Содержание Hydro-Park 1123





















































Результаты поиска

Содержание Hydro-Park 1123

Отзывы:

Бренды по названию

Популярные бренды

MUTRADE Hydro-Park 1123, Руководство пользователя

Результаты поиска

Содержание Hydro-Park 1123

Отзывы:

Бренды по названию

Популярные бренды