Muton ValueJet VJ-1627MH Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 56

background image

26

Setup

Preparation

• Cleaning wiper: 1

• High capacity ink pack adapter: 7

• Cleaning bag: 7

• Ink bag: 7

4 color setting:

Magenta (M), Cyan (C): 2 bags each

Black (K), Yellow (Y), Cleaning (Cl): 1 bag each

5 color setting:

Black (K), Cyan (C), Magenta (M), Yellow (Y), White (Wh): 1 bag each

Cleaning (Cl): 2 bags each

Initial ink charging

1.

Installing the cleaning wiper

[1]

The message on the left will appear.

• Press the [Enter] key.

[2]

Open the right maintenance cover.

[3]

Follow the steps below to install cleaning wiper.

• Slide the front side of the cleaning wiper into its slot.

• Press the wiper hook down until it clicks into place.

Important!

Do NOT touch the cleaning wiper rubber with your bare hand.

If finger oil gets on the rubber, it will damage the print head.

[4]

Close the maintenance cover.

[5]

• Use the [+] or [-] key on Operation panel to select “Installed Wiper?

Yes”.

• Press the [Enter] key.

Installed Wiper ?

->

No

1

2

Installed Wiper ?

->

No

Installed Wiper ?

->

Yes

«
...
24
25
26
27
28
...
»

Содержание ValueJet VJ-1627MH

























































Отзывы:

Нет отзывов

Похожие инструкции для ValueJet VJ-1627MH

ImageCLASS MF3240 Series

Бренд: Canon Страницы: 62

ImageCLASS MF4270

Бренд: Canon Страницы: 226

imageCLASS D660

Бренд: Canon Страницы: 8

ImageCLASS MF3240 Series

Бренд: Canon Страницы: 136

Color imageRUNNER C5180 Series

Бренд: Canon Страницы: 851

imageCLASS D320

Бренд: Canon Страницы: 121

imageCLASS MF212w

Бренд: Canon Страницы: 236

imageCLASS D760

Бренд: Canon Страницы: 82

imageclass LBP251dw

Бренд: Canon Страницы: 72

ImageCLASS MF4270

Бренд: Canon Страницы: 248

ImageCLASS MF4270

Бренд: Canon Страницы: 36

imageCLASS D760

Бренд: Canon Страницы: 8

imageCLASS MF4100 Series

Бренд: Canon Страницы: 140

imageclass LBP251dw

Бренд: Canon Страницы: 116

imageCLASS D860

Бренд: Canon Страницы: 73

imageCLASS D1320

Бренд: Canon Страницы: 36

ImageCLASS MF3240 Series

Бренд: Canon Страницы: 15

imageCLASS D550

Бренд: Canon Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды