MUTOH ValueJet VJ-1624WX Скачать руководство пользователя

Страница: 319 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

6 Maintenance

6.4 Moving or transporting the printer

319

6.4

Moving or transporting the printer

This section describes how to move or transport the printer.

6.4.1

Moving the printer

This section describes how to move the printer.

CAUTION

• When moving the printer, make sure to maintain a horizontal position.

• Do not slant the printer, prop it against a wall or turn it upside down.

The ink inside the printer may leak.
Moreover, normal operation after shifting (to these positions) cannot be guaranteed.

(1) Preparation before moving

When using the dedicated Stands, follow the procedure below to move the printer.

1. Make sure that the printer is turned OFF.

3.2.2 Turning the power OFF

2. Dispose of waste fluid.

6.3 Disposal of waste fluids

3. Remove all the cables, such as Power cord set.

4. Loosen the four adjusters of Stand as shown in the next illustration.

Содержание ValueJet VJ-1624WX







































































































































































































































































































































































Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы:

Похожие инструкции для ValueJet VJ-1624WX

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1624WX, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы:

Похожие инструкции для ValueJet VJ-1624WX

Бренды по названию

Популярные бренды