background image

 

Step 5: Disable and enable EPO function 

Keep the pin 1 and pin 2 closed for UPS normal operation. To activate EPO function, cut the wire 
between pin 1 and pin 2. 

 

 

Step 6: Turn on the UPS   

Press the ON/Mute button on the front panel for two seconds to power on the UPS. 

Note: The battery charges fully during the first five hours of normal operation. Do not expect 
full battery run capability during this initial charge period. 
 

Step 7: Install software 

For optimal computer system protection, install UPS monitoring software to fully configure UPS 
shutdown. You may insert provided CD into CD-ROM to install the monitoring software. If not, 
please follow steps below to download and install monitoring software from the internet:

 

1. Go to the website 

http://www.power-software-download.com

 

2. Click ViewPower software icon and then choose your required OS to download the software.   
3. Follow the on-screen instructions to install the software. 
4. When your computer restarts, the monitoring software will appear as an orange plug icon 
located in the system tray, near the clock. 

 

Step 8: External battery connection

 (for long-run models only) 

Follow below chart to make external   
battery connection. 

                                   

 

It’s in closed status for UPS 

normal operation.   

Содержание POWERMUST 1008 ONLINE LCD



















Отзывы: