background image

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

Mounting Installation

NOTES: 

Dimensions shown for Adult ADA compliant installation. For Child ADA compliant parallel approach installation, 

decrease height of installation by 3 inches. Provide clear floor space as required. Adjust vertical dimensions as required to 
comply with federal, state, and local codes.

Note:
Electrical Service 
Required for Plug-In 
Transformer; Transformer 
does not sit inside Botle 
Filler Box.

 

M-OBR4-GRC

Page 4 of 16

New: 12

/19/17

7020-963-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

 OUTDOOR BOTTLE FILLERS

 

1-1/4" O.D. Bottle Filler/Drinking Fountain Waste

1

2

28

1
2

"

32

1

8

"

4

1
2

"

16"

Stud Frame

Wall Spacing

Ø1"

1
2

"

2"

5
8

"

4"

1
4

"

2

4

1
2

"

1

21"

14

3
8

"

1/4" O.D. Drinking Fountain Supply Inlet

3

1/4" Anchoring Hardware, by others

5/16" Threaded Studs

4

5

2x6 Stud Wall, for reference only

6

4

5

6

6

Mounting Holes

3

GFCI Electrical Service Protected Circuit

7

for -SO Sensor Operated units, by others

26 

7
8

"

A.F.F.

1

13
16

"

7

17"

1

Provide wall opening as indicated in rough-in detail provided. Block-out for bottle filler box and provide structural support

for mounting plate ø1/4” anchoring holes provided.

Содержание M-OBR4-GRC Series

















Отзывы: