Munters BI28M Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

Munters BI28M Скачать руководство пользователя страница 6

FORM: QM1110M

Rev. 1, November 2013

Page 6 of 12

Munters Corporation

4215 Legion Dr. Mason, MI 48854-1036 USA
Ph: +1 517 676-7070 Fax: +1 517 676-7078
www.munters.us

Step 3C

At the middle of the long side of the insulation
stop,12,7 mm down from the top, drill or punch a 6,35
mm dia. hole on each side of the insulation stop.

See

Figure 3C.

Step 3D

Install (1) Retaining Clip [C] on each end of the
fi berglass rod. The Retaining Clip should be 38,1 mm
from the end of the rod. Then insert the end of the
rod through the new hole in the insulation stop from
the inside out. Insert the other end of the rod through
the hole in the other side of the insulation stop. Install
the remaining Retaining Clip [C] on each end of the
fi berglass rod, so that the insulation stop is between 2
of the clips.

See Figure 3D.

Figure 3C

Insulation Stop

Insulation Stop

Long side of
frame

Rod

Figure 3D

Retaining Clip [C]

Insulation Stop

6,35 dia. hole

6,35 dia. hole

12,7
mm

«
...
4
5
6
7
8
...
»

Содержание BI28M













Отзывы:

Нет отзывов