manualshive.com logo in svg

Munters BI28M, Руководство пользователя и инструкция по установке, Страница: 3 / 12

Поделиться
Скачать
Munters BI28M Скачать руководство пользователя страница 3

FORM:  QM1110M

Rev. 1, November  2013

Page 3 of 12

Munters Corporation

4215 Legion Dr.  Mason, MI  48854-1036  USA
Ph: +1 517 676-7070    Fax: +1 517 676-7078    
www.munters.us  

  Each BI28M/BI48M includes:

1 – Plastic Frame with 2 doors attached
1 – Insulation Stop, 304,8 mm tall
1 – Fiberglass Rod (BI48M) only
1 – Hardware package as follows:

  

HP1240 for BI28M 

[A]....8 – #9- 15 x 38,1 mm Hex Head Screw
[B]....1 – 4,7 mm Dia. Cable Clamp

  

HP1248 for BI48M 

[A]....12 – #9 - 15 x 38,1 mm Hex Head Screw
[B]....1 – 4,7 mm Dia. Cable Clamp
[C]....4 – 6,3 mm Dia. Retainer Clips

Before beginning installation, check the overall condition of the equipment. Remove packing 

materials, and examine all components for signs of shipping damage. Any shipping damage is the 
customer's responsibility and should be reported immediately to your freight carrier.

UNPACKING THE EQUIPMENT

[A]

[B]

[C]

15,3 mm

106,3 mm

A

700 mm

DIMENSIONS

End View

Side View

Inlet A

BI28 798,5 

mm

BI48 1331,9 

mm

Содержание BI28M













Отзывы:

Нет отзывов