Multitech MultiMobile MT56128ZLX-NT Скачать руководство пользователя страница 13

Страница: 13 / 96

MultiMobile

Chapter 2—Hardware/Driver Installation

Windows 95/98 Installation—VCOMM & CAPI

Before you start

In Windows 95, you MUST install the drivers before

attaching the PC Card to your laptop.

If you install the PC Card first, the

operating system wont recognize the device.
1. Click

Start

Settings

Control Panel, and Add/Remove Programs.

Then click

Install

2. The

Install Program From Floppy Disk or CD-ROM

dialog box

appears. Insert the MT56128ZLX-ST Disk 1 and click

Next

3. The

Run Installation Program

dialog box appears. Click

Finish

4. The

Setup

dialog box appears and informs you that the Configuration

Utility Setup is preparing the InstallShield Wizard (which guides you

through the setup).

5. The

Welcome

dialog box appears. Click

Next

6. The

Choose Destination Location

dialog box appears. Click

Next

install to the destination folder listed in the dialog box. (Click

Browse

to install to a different folder.)

7. The

Select Program Folder

dialog box appears. Select a folder or type

a new folder name. Then click

Next

8. The

Start Copying Files

dialog box appears. Click

Back

to review or

change settings. To begin copying files, click

Next

9. As the files copy, the

Setup Needs The Next Disk

dialog box appears

and, in sequence, requests Disk 2, Disk 3, and Disk 4 (key disk). Insert

each requested disk and click

. The driver installs with each disk.

10. The

Configuration Utility

window and the

Com Port Change

dialog

box appear. Make appropriate changes in the

Com Port Change

dialog

box, if necessary, and then click

11. The

Microsoft ISDN Accelerator Pack 1.1

dialog box appears and

asks if you want to install the accelerator pack. (This dialog box does

not appear in Windows 98 since the Accelerator Pack is already

included in Windows 98.) If it is not installed on your computer, click

Yes

and follow dialog box instructions. If it is already installed, click

and close the

Configuration Utility

window.

Содержание MultiMobile MT56128ZLX-NT

































































































Результаты поиска

Содержание MultiMobile MT56128ZLX-NT

Отзывы:

Похожие инструкции для MultiMobile MT56128ZLX-NT

Бренды по названию

Популярные бренды

Multitech MultiMobile MT56128ZLX-NT, Руководство пользователя

Результаты поиска

Содержание MultiMobile MT56128ZLX-NT

Отзывы:

Похожие инструкции для MultiMobile MT56128ZLX-NT

Бренды по названию

Популярные бренды