background image

page 28 — HHXd5 RIde-ON TROWeL • OpeRaTION maNuaL — Rev. #2 (05/04/12) 

Maintenance

Oil/Water Separator

Drain water from the bottom of the fuel filter by loosening 

the drain plug and allowing the water to drain out. Refer 

to your engine manual for specific details to perform this 

operation.

Oil and Fuel Lines

1.  Check the oil and fuel lines and connections regularly 

for leaks or damage. Repair or replace as necessary.

2.  Replace  the  oil  and  fuel  lines  every  two  years  to 

maintain the line's performance and flexibility.

Radiator/Cooling System

1.  Check and clean radiator fins.
2.  Check cooling water.
3.  Check radiator hoses for fatigue or cracking.
4.  Check radiator cap seal.

Battery/Charging System

  WaRNINg

Hot coolant can cause severe burns. DO NOT remove 

cap if radiator is HOT.

1.  Check and clean battery terminals for corrosion.
2.  Check and keep battery electrolyte between upper and 

lower limits indicated on the battery.  Never operate or 

recharge without sufficient fluid in the battery.

3.  Never attempt to charge a battery that is frozen. The 

battery can explode unless first allowed to thaw. 

4.  Disconnect the negative terminal ( - ) of the battery 

during storage. If unit will be stored where ambient 

temperature will drop to -15

o

C or less, remove and 

store battery in a warm, dry place.

Long Term Storage

 

„

Remove the battery.

 

„

Drain fuel from fuel tank. 

 

„

Clean exterior with a cloth soaked in clean oil. 

 

„

Store unit covered with plastic sheet in moisture and 

dust-free location out of direct sunlight.

engine Tune-up

See your engine manual for specific information on tuning 

up your engine.

  CauTION

Never store the ride-on trowel with fuel in the tank for 

any extended period of time. Always clean up spilled 

fuel immediately.

 NOTICE

See the engine manual supplied with your machine 

for  appropriate  engine  maintenance  schedule  and 

troubleshooting guide for problems.

  CauTION

ALWAYS disconnect battery cables before attempting 

any service or maintenance on the ride-on trowel.

  daNgeR

Use  all  safety  precautions  specified  by  the  battery 

manufacturer when working with the battery.

Flammable,  explosive  gas.  (produces 

hydrogen  gas  while  charging  or  during  

operation). Keep area around battery well 

ventilated and keep from any fire source.
Battery electrolyte contains corrosive, toxic 

chemical.  (dilute  sulfuric  acid).  Avoid 

contact with eyes and skin.
Shock  or  Fire  due  to  electric  short-

circuit. Disconnect battery cables before 

inspecting  electrical  system  and  never 

"spark"  battery  terminals  to  test  for 

charge.

Содержание WHITEMAN HHXD5























































Отзывы:

Похожие инструкции для WHITEMAN HHXD5