background image

HHXd5 RIde-ON TROWeL • OpeRaTION maNuaL — Rev. #2 (05/04/12) — page 11

Safety infOrMatiOn

  NOTICE

 

„

NeveR run engine without an air fi lter or with a dirty air 

fi lter. Severe engine damage may occur. Service air fi lter 

frequently to prevent engine malfunction.

 

„

NeveR  tamper  with  the  factory  settings 

of the engine or engine governor. Damage 

to  the  engine  or  equipment  can  result 

if  operating  in  speed  ranges  above  the 

maximum allowable.

FueL SaFeTY

  daNgeR

 

„

dO NOT start the engine near spilled fuel or combustible 

fl uids. Fuel is extremely fl ammable and its vapors can 

cause an explosion if ignited. 

 

„

aLWaYS  refuel  in  a  well-ventilated  area,  away  from 

sparks and open fl ames. 

 

„

aLWaYS  use  extreme  caution  when  working  with 

fl ammable liquids. 

 

„

dO NOT fi ll the fuel tank while the engine is running 

or hot.

 

„

dO NOT overfi ll tank, since spilled fuel could ignite if it 

comes into contact with hot engine parts or sparks from 

the ignition system. 

 

„

Store fuel in appropriate containers, in well-ventilated 

areas and away from sparks and fl ames.

 

„

NeveR use fuel as a cleaning agent.

 

„

dO  NOT  smoke  around  or  near  the 

equipment. Fire or explosion could result 

from fuel vapors or if fuel is spilled on a 

hot engine.

BaTTeRY SaFeTY

  daNgeR

 

„

dO NOT drop the battery. There is a possibility that the 

battery will explode.

 

„

dO NOT expose the battery to open fl ames, 

sparks, cigarettes, etc. The battery contains 

combustible  gases  and  liquids.  If  these 

gases and liquids come into contact with a 

fl ame or spark, an explosion could occur.

  WaRNINg

 

„

aLWaYS  wear  safety  glasses  when 

handling the battery to avoid eye irritation. 

The battery contains acids that can cause 

injury to the eyes and skin.

 

„

Use well-insulated gloves when picking up 

the battery.

 

„

aLWaYS keep the battery charged. If the battery is not 

charged, combustible gas will build up.

 

„

dO NOT charge battery if frozen. Battery can explode. 

When frozen, warm the battery to at least 61°F (16°C).

 

„

aLWaYS  recharge  the  battery  in  a  well-ventilated 

environment to avoid the risk of a dangerous concentration 

of combustible gases.

 

„

If  the  battery  liquid  (dilute  sulfuric  acid) 

comes into contact with 

clothing or skin

rinse  skin  or  clothing  immediately  with 

plenty of water.

 

„

If  the  battery  liquid  (dilute  sulfuric  acid)  comes  into 

contact with 

eyes, rinse eyes immediately with plenty 

of water and contact the nearest doctor or hospital to 

seek medical attention.

  CauTION

 

„

aLWaYS disconnect the NegaTIve battery terminal 

before performing service on the equipment.

 

„

aLWaYS keep battery cables in good working condition. 

Repair or replace all worn cables.

Содержание WHITEMAN HHXD5























































Отзывы:

Похожие инструкции для WHITEMAN HHXD5