background image

page 22 — HHXd5 RIde-ON TROWeL • OpeRaTION maNuaL — Rev. #2 (05/04/12) 

inSpectiOn

This  section  is  intended  to  assist  the  operator  with  the 

initial start-up of the HHX. It is extremely important that 

this section be read carefully before attempting to use the 

trowel in the field.
dO NOT use your ride-on power trowel until this section is 

thoroughly understood.

See Figure 2, Figure 3 and Figure 4 for the location of any 

control or indicator referenced in this manual.

eNgINe OIL LeveL

1.  Lift (tilt) seat forward to access dipstick.
2.  Pull the engine oil dipstick from its holder.
3.  Determine if engine oil is low (Figure 7), add 

correct amount of engine oil to bring oil level 

to a normal safe level (See Recommended 

Viscosity Grades, Table 5)..

Figure 7. Engine Oil Dipstick

geaRBOX OIL LeveL

1.  Check the gearbox oil level in both gearboxes 

by viewing the sight glass at the rear of the 

gearbox. See Figure 8. 

2.  The oil level of the gear box should be at the 

half-way point of the sight glass (Figure 8). The gear 

  WaRNINg

Failure to understand the operation of the HHX could 

result in severe damage to the trowel or personal injury.

  CauTION

DO NOT overfill engine oil. Oil level should not be above 

the top fill line. 

MAX

MIN

ADD OIL

DIPSTICK

SAFE

OPERATING

LEVEL

DO NOT

OVERFILL

box  oil  capacity  is  1  U.S.  Gallon,  (3.79  liters).    If 

additional  oil  is  required,  unscrew    the  oil  fill    plug 

located on top of the gearbox, and refill with ISO 220 

A GMA GR 5 EP oil.

Figure 8. Gearbox Oil Plugs

FueL

To determine if the engine fuel is low, view the sight gauge 

on the side of the fuel tank. If fuel level is low, fill with clean 

Diesel fuel.

HYdRauLIC FLuId FILTeR

To determine if the hydraulic fluid filter needs to be changed, 

view  the  sight  gauge  above  the  hydraulic  filter  located 

beneath the foot platform.. If the gauge reads in the red 

area, indicating a fiter by-pass condition, the filter needs 

to be replaced.

DRAIN PLUG

SIGHT GLASS

(OIL CHECK)

FILL PLUG

  WaRNINg

Handle fuel safely. Motor fuels are highly flammable and 

can be dangerous if mishandled. 

dO NOT smoke while 

refueling. Do not attempt to refuel the ride-on trowel if 

the engine is hot or running.

  WaRNINg

Never  store  the  ride-on  trowel  with  fuel  in  the  tank 

for  any  extended  period  of  time.  Drain  fuel  into  an 

appropriate  recepticle.  Drain  by  opening  the  fuel 

petcock  at  the  bottom  of  the  tank.  Always  clean  up 

spilled fuel immediately.

Содержание WHITEMAN HHXD5























































Отзывы:

Похожие инструкции для WHITEMAN HHXD5