manualshive.com logo in svg

MULTIQUIP Power WHISPERWATT DCA400SSI, Руководство по эксплуатации и частям

Поделиться
Скачать
MULTIQUIP Power WHISPERWATT DCA400SSI Скачать руководство пользователя страница 30

PAGE 30 — DCA400SSI GENERATOR • OPERATION AND PARTS MANUAL — REV. #2 (11/03/08) 

INSPECTION/SETUP

CIRCUIT BREAKERS

To protect the generator from an overload, a 3-pole, 600 
amp, main circuit breaker is provided to protect the 

U,V, 

and W Output Terminals

 from overload. In addition two 

single-pole, 20 amp 

GFCI 

circuit breakers are provided to 

protect the GFCI receptacles from overload. Three 50 amp 

load

 circuit breakers have also been provided to protect the 

auxiliary receptacles from overload. Make sure to switch 

ALL

 circuit breakers to the 

OFF

 position prior to starting 

the engine.

LUBRICATION OIL

Fill the engine crankcase with lubricating oil through the 
fi ller hole, but 

DO NOT

 overfi ll. Make sure the generator is 

level and verify that the oil level is maintained between the 
two notches (Figure 27) on the dipstick. See Table 11 for 
proper selection of engine oil.

Engine Oil Dipstick

Figure 27. 

When checking the engine oil, be sure to check if the oil is 
clean. If the oil is not clean, drain the oil by removing the 
oil drain plug, and refi ll with the specifi ed amount of oil as 
outlined in the 

ISUZU Engine Owner’s Manual

. Oil should 

be warm before draining.

Other types of motor oils may be substituted if they meet 
the following requirements:

 API Service Classifi cation CC/SC

 

API Service Classifi cation CC/SD

 

API Service Classifi cation CC/SE

 

API Service Classifi cation CC/SF

 

Recommended Motor Oil

Table 11. 

FUEL CHECK

Refi lling the Fuel System 

This generator has an internal fuel tank located inside 
the trailer frame and may also be equipped with an 
environmental fuel tank (Figure 28). 

ALWAYS

 fi ll the fuel 

tanks with clean fresh 

#2 diesel fuel. DO NOT

 fi ll the fuel 

tanks beyond their capacities.

Pay attention to the fuel tank capacity when replenishing 
fuel. The fuel tank cap must be closed tightly after fi lling. 
Handle fuel in a safety container. If the container does not 
have a spout, use a funnel. Wipe up any spilled fuel 
immediately.

Internal Fuel Tank System

Figure 28. 

  DANGER

Fuel spillage on a 

hot

 engine can cause 

a 

fi re

 or 

explosion

. If fuel spillage occurs, 

wipe up the spilled fuel completely to 
prevent fire hazards. 

NEVER

 smoke 

around or near the generator.

  CAUTION

ONLY properly trained personnel

 who have read 

and understand this section should refi ll the fuel tank 
system.

Содержание Power WHISPERWATT DCA400SSI



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды