manualshive.com logo in svg

MULTIQUIP Power WHISPERWATT DCA400SSI, Руководство по эксплуатации и частям

Поделиться
Скачать
MULTIQUIP Power WHISPERWATT DCA400SSI Скачать руководство пользователя страница 18

PAGE 18 — DCA400SSI GENERATOR • OPERATION AND PARTS MANUAL — REV. #2 (11/03/08) 

GENERATOR CONTROL PANEL

Generator Control Panel

Figure 4. 

The defi nitions below describe the controls and functions 
of the DCA400SSI Generator Control Panel (Figure 4).

Pilot Lamp 

1. 

— Indicates the system is running.

Panel Light 

2. 

— Normally used in dark areas or at night 

time. When activated, panel lights will illuminate. When 
the generator is not in use be sure to turn the panel 
light switch to the 

OFF

 position.

AC Voltmeter 

3. 

— Indicates the output voltage present 

at the 

U,V, and W Output Terminal Lugs.

Frequency Meter 

4. 

— Indicates the output frequency 

in hertz (Hz). Normally 60 Hz.

AC Ammeter 

5. 

— Indicates the amount of current the 

load is drawing from the generator per leg selected by 
the ammeter phase-selector switch.

Voltmeter Change-Over Switch 

6. 

— This switch allows 

the AC voltmeter to indicate phase to phase voltage 
between any two phases of the output terminals or to 
be switched off.

Ammeter Change-Over Switch 

7. 

— This switch allows 

the AC ammeter to indicate the current fl owing to the load 
connected to any phase of the output terminals, or to be 
switched off. This switch does not effect the generator 
output in any fashion, it is for current reading only.

Panel Light Switch 

8. 

— When activated will turn on 

control panel light.

Voltage Regulator Control 

9. 

— Allows ±15% manual 

adjustment of the generator’s output voltage.

Main Circuit Breaker 

10. 

— This three-pole, 1,000 amp 

main breaker is provided to protect the 

U,V, and W 

Output Terminal  Lugs

 from overload.

Auto On/Off Engine Controller (MPEC) 

11. —

 

This controller has a vertical row of status LED’s (inset), 
that when lit, indicate that an engine malfunction (fault) 
has been detected. When a fault 
has been detected the engine 
controller will evaluate the fault 
and all major faults will shutdown 
the generator. During 

cranking 

cycle

, The MPEC will attempt to 

crank the engine for 10 seconds 
before disengaging.

 

If the engine does not engage (start) by the third 
attempt, the engine will be shutdown by the engine 
controller’s 

Over Crank Protection

 mode. If the 

engine engages at a speed (RPM’s) that is not safe, 
the controller will shutdown the engine by initializing 
the 

Over Speed Protection 

mode.

Содержание Power WHISPERWATT DCA400SSI



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды