manualshive.com logo in svg

MULTIQUIP Power WHISPERWATT DCA400SSI, Руководство по эксплуатации и частям

Поделиться
Скачать
MULTIQUIP Power WHISPERWATT DCA400SSI Скачать руководство пользователя страница 10

PAGE 10 — DCA400SSI GENERATOR • OPERATION AND PARTS MANUAL — REV. #2 (11/03/08) 

SAFETY INFORMATION

ELECTRICAL SAFETY

  DANGER

DO NOT

 

 touch output terminals during 

operation. Contact with output terminals 
during operation can cause 

electrocution, 

electrical shock or burn.

The electrical voltage required to 

 

operate the generator can cause severe injury or even 
death through physical contact with live circuits. Turn 
generator and all circuit breakers 

OFF

 before performing 

maintenance on the generator or making contact with 
output terminals.

NEVER

 

 insert any objects into the output 

receptacles during operation. This is 
extremely dangerous. The possibility 
exists of 

electrical shock, electrocution 

or death. 

 

Backfeed to a utility system can cause 

 

electrocution

 and/or property damage. 

NEVER 

connect the generator to a 

building’s electrical system without 
a transfer switch or other approved 
device. All installations should be performed by a 

licensed electrician

 in accordance with all applicable 

laws and electrical codes. Failure to do so could result 
in electrical shock or burn, causing 

serious injury or 

even death.

Power Cord/Cable Safety

  DANGER

NEVER

 

 let power cords or cables 

lay in water.

NEVER stand in water 

 

while AC power from the 

generator is being transferred to a load.

NEVER

 

 use 

damaged

 or 

worn 

cables or cords when 

connecting equipment to generator. Inspect for cuts in 
the insulation. 

NEVER

 

 grab or touch a live power 

cord or cable with wet hands. The 
possibility exists of 

electrical shock, 

electrocution or death. 

Make sure power cables are securely connected to the 

 

generator’s output receptacles. Incorrect connections 
may cause electrical shock and damage to the 
generator.

NOTICE

ALWAYS 

 

make certain that proper power or extension

cord has been selected for the job. See Cable Selection 
Chart in this manual.

Grounding Safety

  DANGER

ALWAYS

 

 make sure that electrical circuits are properly 

grounded to a suitable earth ground (ground rod) per 
the National Electrical Code (NEC) and local codes 
before operating generator. 

Severe injury or death by 

electrocution

 can result from operating an ungrounded 

generator.

NEVER

 

 use gas piping as an electrical ground.

Содержание Power WHISPERWATT DCA400SSI



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды