background image

PAGE 27 — JTNSW20-24HTCSL SERIES RIDE-ON TROWEL • OPERATION MANUAL — REV. #1 (3/24/16) 

MAINTENANCE 

Fuel Filter (200 Hours) 

1.  Replace the engine fuel filter (Figure 18) every 200 hours.

Figure 18. Honda Fuel Filter

FUEL FILTER CHANGE

1.  Replace the engine fuel filter (Figure 19) every year or 

300 hours.

Figure 19. Fuel Filter

SPARK PLUG ADJUSTMENT

1.  Make sure the engine is cool before servicing the 

spark plugs.

2.  Disconnect the spark plug caps. Check for dirt and 

remove any dirt from around the spark plug area.

3.  Remove the spark plugs with a 5/8-inch spark plug 

wrench.

4.  If the spark plugs are damaged, the sealing washer is 

in poor condition, or if the electrode is worn, replace 

the spark plugs.

5.  Measure the spark plug electrode gap (Figure 20) with 

a wire-type feeler gauge. If needed, adjust the gap to 

0.7 - 0.8 mm (0.028 - 0.031 in), by carefully bending 

the side electrode.

Figure 20. Spark Plug Gap Adjustment

6.  Install the spark plug carefully, by hand, to avoid cross 

threading.

7.  After the spark plug is seated, tighten with a 5/8-inch 

spark plug wrench to compress the sealing washer.

8.  When installing a new spark plug, tighten 1/2 turn, after 

the spark plug seats, to compress the washer.

9.  When reinstalling the original spark plug, tighten 1/8 1/4 

turn after the spark plug seats to compress the washer.

10.  Reattach the spark plug caps

ENGINE TUNE-UP ENGINE

See your engine manual for specific information on tuning up 

your engine, checking and gaping the spark plugs, etc. 

LONG TERM STORAGE

 

„

Drain the fuel tank completely, or add STA-BIL to the fuel.

 

„

Remove spark plug and pour a few drops of motor oil into 

cylinder. Crank engine 3 to 4 times so that oil reaches 

all internal parts. 

 

„

Clean exterior with a cloth soaked in clean oil. 

 

„

Remove the battery.

 

„

Store unit covered with plastic sheet in moisture and 

dust-free location out of direct sunlight.

 

„

GAP

.024 - .028 IN.

(0.6- 0.7 MM.)

 NOTICE

See the engine manual supplied with your machine 

for appropriate engine maintenance schedule and 

troubleshooting guide for problems.

 CAUTION

NEVER

 store the ride-on trowel with fuel in the tank for 

any extended period of time. Always clean up spilled fuel 

immediately.

Содержание JTNSW20HTCSL















































Отзывы: