Operating Instructions for Power Set „DogFighter TUNING“
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 1/2
O
p
e
ra
ti
o
n
i
n
s
tr
u
c
ti
o
n
s
f
o
r
P
o
w
e
r
s
e
t
„D
o
g
F
ig
h
te
r
T
U
N
IN
G
“
#
8
2
5
9
5
1
(1
0
-0
6
-0
2
/D
A
M
A
)
E
rr
o
rs
a
n
d
o
m
is
s
io
n
s
e
x
c
e
p
te
d
!
M
U
L
T
IP
L
E
X
!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
Our "DogFighter TUNING" power set, # 33 2656, consists
of a set of components which are perfectly matched to
each other. It offers extreme performance for high-speed
models, and opens up a new field of speed and vertical
climbing ability to the model pilot.
2. C
ONTENTS
/
R
EPLACEMENT PARTS
•
1 Himax C 3516-1130 motor
# 33 3023
•
1 MULTIcont BL-40 BL speed controller
# 7 2285
•
1 10” x 7” propeller
# 73 3115
•
1 propeller driver and nut for ELAPOR spinner
Motor shaft-Ø 5mm, Prop-shaft 6 mm
# 33 2326
•
Various small items for installation in the model
3. T
YP
.
O
PERATIONAL
D
ATA OF
P
OWER
S
ET
“D
OG
F
IGHTER
TUNING”
3S LiPo / Prop: 10“ x 7“ Current drain: approx. 35.0 A
Recommended Battery:
MULTIPLEX Li-BATT FX 3/1-2200 (M6) # 15 7351
If you use the Himax C 3516-1130 motor and the
standard propellers supplied in the set, do not use more
than a 3S LiPo pack or 9 NiXX cells
.
4.
S
AFETY
N
OTES
The power set “DogFighter TUNING” is designed
exclusively for use in modelling applications. Incorrect
use can result in serious personal injury.
•
Read the instructions before initiation
•
Before every flight, check that the motor and propeller
are securely mounted
•
Remove all movable objects from the area around the
propeller before switching the motor on
•
Do not allow clothing or any of your extremities to get
close to the spinning propeller
•
Never run the motor in your hand
•
Switch the motor off immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the
propeller
•
Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
5. A
SSEMBLING
O
F
T
HE
P
OWER
S
ET
“D
OG
F
IGHTER
TUNING”
1. Screw the motor to the motor mount.
ensure that the motor is free to rotate. When
deploying the motor cables, check that they cannot
make contact with the spinning motor. Secure the
motor leads with Velcro tape or similar.
2. Fit the split taper collet and the propeller driver on the
motor shaft.
3. Fit the propeller and the spinner holder on the propeller
driver, and secure them with the nut for the ELAPOR
spinner (supplied).
4. Clip the ELAPOR spinner onto the spinner holder.
