background image

Visit 

gomultilink.com

 for new product releases!

INST

ALL

ATION

Cop

yrigh

t © 2019 Multilink I

nc

. A

ll righ

ts r

eser

ved  •  Sp

ecific

ations subjec

t t

o change without notic

e  •  Re

v. 11/20/2019  •

Page 5

Do

cu

men

t N

o.

 O

pti

ma

 16

 Ins

tal

la

tio

n G

ui

de

3. General Warnings

3.1 Laser Light Warning

Never look directly into the end of a fiber that may be carrying laser light. Laser light 

can be invisible and may be harmful to your eyes. Viewing it directly may not cause pain; 

therefore it will not cause blinking or the iris of the eye to close involuntarily as it does when 

viewing bright light. Consequently, serious damage to the retina of the eye is possible. Should 

accidental exposure of laser light be suspected, arrange an eye exam immediately.

3.2 Laser Light Magnification Warning

Do not use magnifiers in the presence of laser radiation. Diffused laser light can cause 

serious eye damage if focused with optical instruments. 

3.3 Loose Fiber Warning

Cleaved or broken glass fibers are very sharp and can pierce the skin easily. Keep your 

work area clear of removed fiber. Do not allow pieces of fiber to stick to your clothing or fall 

into the work area where they can cause injury later. Use tweezers to pick up broken/cut 

pieces of fiber and place on a piece of tape that has been set aside for this purpose.

3.4 Sharp Edge Warning

The wearing of cut-resistant safety gloves to protect your hands from sharp cutting 

tools and the metal armoring of armored cable is strongly recommended. Use extreme care 

when working with severed armor. There may be sharp edges where the armor is damaged. 

Always cover the exposed/cut armor end with a wrap of black electrical tape. To minimize the 

chance of injury from sharp-blade tools, always cut away from yourself and others. Dispose of 

used blades and armor scrap properly.

3.5 Safety Glasses Warning

Use safety glasses while working is highly recommended to provide eye protection 

from accidental injury when handling chemicals, cables or working with fiber. Pieces of glass 

fiber are very sharp and have potential to damage the eye.

3.6 Electrical Shock Warning

Do not install telecommunications equipment or work with telephone wiring during 

a lightning storm. Telephone lines can carry high voltages from lightning causing electrical 

shock resulting in severe injury or death.

3.7 Fiber Damage Warning

Fiber Optic cable is highly sensitive to excessive pulling, bending and crushing. Take 

care when bending the cables. Be sure not to pull too hard on the fibers. Do not crush the 

cable or allow it to kink. Doing any of these things may cause damage to the fiber and require 

it to be replaced.

Содержание Optima 16


















Отзывы: