background image

26

27

Copyright Notice & Disclaimers

Board Overview

Copyright Notice & Disclaimers

Copyright © 2017 Multicom Systems Pty Ltd. All rights reserved

Multicom BMC-3G Installation Guide - November 29, 2017 edition
Maintenance Release V1.7

Please address your comments and suggestions to Multicom Systems on  
1300 65 44 33. 

Changes may be made periodically to the information in this publication.  
The changes will be incorporated in new editions of the guide.

This guide and the software described in this document is furnished under 
a license agreement, and may be used or copied only in accordance 
with the terms thereof. It is against the law to copy the user guide and 
software on any other medium, except as specifically provided in the 
license agreement. The licensee may make one copy of the software for 
backup purposes. 

No part of this publication may be reproduced, stored in a retrieval 
system, or transmitted in any form or by any means, electronic, 
mechanical, photocopied, recorded or otherwise, without the prior 
written permission of Multicom Systems Pty Ltd.

The software license and limited warranty for the accompanying products 
are set forth in the information packet supplied with the product, and are 
incorporated herein by this reference. If you cannot locate the software 
license, contact your Multicom Systems representative for a copy.

All product names mentioned in this manual are for identification 
purposes only, and are either trademarks or registered trademarks of their 
respective owners.

BMC-3G

Signal Strength LEDs

Current SMS in use

Fault LED

3G connection status

Communications LED

Tamper connection

Board Overview

Содержание BMC-3G


















Отзывы: