manualshive.com logo in svg

MULTICHANNEL SYSTEMS MEA 1060-Inv, Руководство пользователя

Поделиться
Скачать
MULTICHANNEL SYSTEMS MEA 1060-Inv Скачать руководство пользователя страница 9

9 

3 

First Use of the MEA Amplifier 

3.1  Welcome to the MEA Amplifier 

 

Raw data from up to

 60 electrodes

 of a 

microelectrode array

 (

MEA

) is amplified  

by 

60 channels

 of 

filter amplifiers

 that are built very small and compact using SMD  

(Surface Mounted Devices) technology. The small-sized MEA amplifier combines the  

interface

 to the 

MEA probe

 with the 

signal filtering

 and the 

amplification

 of the signal.  

The compact design reduces line pick up and keeps the noise level down. 

The 

MEA sensor

 is placed directly into the small-sized MEA 

amplifier

. When the amplifier  

is closed, the 

contact pins

 in the lid of the amplifier are pressed onto the MEA 

contact pads

. 

The very close location of the amplifier to the MEA sensor is very favorable concerning a high 
signal-to-noise ratio. 

MEA amplifiers can be ordered with different 

gain

 and 

bandwidth

 configurations by the user's 

choice. For example, typical pass bands would be 1 to 300 Hz for recording field potentials and 
300 to 3000 Hz for recording action potentials. It is also possible to use a broadband amplifier  
and filter the data with the digital filter of the free MC_Rack program. Gain settings from  
100 to 5000 are possible. 

The amplifier is connected to the 

data acquisition

 computer via a single 

68-pin MCS standard 

cable

. The analog output signals of the MEA amplifier are then acquired and digitized by the 

MC_Card (MEA-System) or your custom data acquisition system. 

MEA amplifiers have an 

integrated heating system

 for controlling the 

MEA's temperature

. 

The desired temperature can be easily programmed with a temperature controller. You will not 
need an incubator during recording all environmental conditions are reliably controlled directly  
in the MEA dish. 

You can then simply 

ground

 bad or unwanted electrodes by toggling small switches on the 

amplifier. You can also connect a stimulus generator to any electrode(s) for 

stimulation

. 

Amplifier inputs are grounded during stimulation to prevent a saturation of the amplifier. 

Содержание MEA 1060-Inv




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды