Multi-Tech MultiFrad FR3060, Руководство пользователя

Страница: 101 / 105

101
Glossary
Robbed Bit Signaling: The popular T1 signaling mechanism where the A and B bits are sent by each side of the T1 termination and are
"buried" in the voice data of each voice channel in the T1 circuit. Since the bits are "robbed" infrequently, voice quality is remains
relatively uncompromised. See "bit robbing".
The robbed-bit signaling technique is used in D4 channel banks to convey signaling information. The eighth (least significant) bit of each
of the 24 8-bit time slots is "robbed" every sixth frame to convey voice-related signaling information such as on-hook, off-hook, etc., for
each channel.
MultiFRAD: A device that connects two networks using the same networking protocol. It operates at the Network Layer (Layer 3) of the
OSI model for forwarding decisions.
Routing Information Protocol (RIP): A distance vector-based protocol that provides a measure of distance, or hops, from a transmit-
ting workstation to a receiving workstation.
RS232-C: An EIA standard for a serial interface between computers and peripheral devices (modem, mouse, etc.). It uses a 25-pin DB-
25, or a 9-pin DB-9 connector. The RS-232 standard defines the purposes, electrical characteristics and timing of the signals for each of
the 25 lines.
RS-422: The EIA standard for a balanced interface with no accompanying physical connector. RS-422 products can use screw
terminals, DB-9, various DB-25, and DB-37 connectors.
RS-530: The EIA standard for the mechanical/electrical interface between DCEs and DTEs transmitting synchronous or asynchronous
serial binary data. RS-530 provides for high data rates with the same connector used for RS-232; however, it is incompatible with RS-
232.
S
Serial Port: The connector on a PC used to attach serial devices (those that need to receive data one bit after another), such as a
mouse, a printer or a modem. This consists of a 9- or 25-pin connector that sends data in sequence (bit by bit). Serial ports are referred
to as "COMx" ports, where x is 1 to 4 (i.e., COM1 through COM4). A serial port contains a conversion chip called a "UART" which
translates between internal parallel and external serial formats.
Service: The requirements offered by an RPOA to its customers to satisfy specific telecommunications needs.
Severely Errored Seconds (SES): Refers to a typical T1 error event where an error burst occurs (a short term, high bit-error rate that
is self-clearing). Per the ITU-T (CCITT) G.821: any second in which the BER is less than 1x10
-3
.
Signaling: The process of establishing, maintaining, accounting for, and terminating a connection between two endpoints (e.g., the
user premises and the telco CO). Central office signals to the user premises can include ringing, dial tone, speech signals, etc. Signals
from the user's telephone can include off-hook, dialing, speech to far-end party, and on-hook signals.
In-band signaling techniques include pulse and tone dialing. With common channel signaling, information is carried out-of-band.
Simple Network Management Protocol (SNMP): TCP/IP protocol that allows network management.
Simultaneous Voice Data (SVD): A technology for letting a user send data via a modem, and use a handset to talk to another user at
the same time over the same connection. The alternative, making a second call, can be expensive or even impossible. The uses for
SVD are telecommuting, videoconferencing, distant learning, tech support, etc.
Stop Bit: One of the variables used for timing in asynchronous data transmission. Depending on the devices, each character may be
trailed by 1, 1.5, or 2 stop bits.
Superframe (D4): A T1 transmission format that consists of 12 DS1 frames, or 2316 bits. A DS1 frame consists of 193 bit positions. A
frame overhead bit is in the first position, and it is used for frame and signaling phase alignment only.
Subscriber Loop: See "Local loop".
Switched 56: A circuit-switched (full duplex digital synchronous data transmission) service that lets you dial a number and transmit data
to it at 56K bps. It is a relatively low cost service, widely used in North America for telecommuting, videoconferencing and high speed
data transfers. Many phone companies are (or will be) phasing out Switched 56 in favor of ISDN service.
Switched Virtual Circuit (SVC): A type of data transmission where the connection is maintained only until the call is cleared.
Switched Line: In communications, a physical channel established by dynamically connecting one or more discreet segments. This
connection lasts for the duration of the call after which each segment may be used as part of a different channel. Contrast with leased
line.
Switched Network: A network in which a temporary connection is established from one point via one or more segments.
Synchronous Data Link Control (SDLC): A discipline conforming to subsets of the Advanced Data Communications Control Proce-
dures (ADCCP) of the American National Standards Institute (ANSI) and High-level Data Link Control (HDLC) of the International
Organization for Standardization, for managing synchronous, code-transparent, serial-by-bit information transfer over a link connection.
Transmission exchanges may be duplex, or half-duplex over switched or nonswitched links. The configuration of the link connection may
be point-to-point, multipoint, or loop.