manualshive.com logo in svg

Mueller 8824390, Инструкция по установке и эксплуатации, Страница: 25 / 46

Поделиться
Скачать
Mueller 8824390 Скачать руководство пользователя страница 25

    

Mueller E-Star OESE 7.5 and 9 HP HFC Condensing Unit   

Installation and Operation Manual, Part No. 8828748 

 

 

Effective June 16, 2020 

 

9.3 

RGE ELECTRONIC FAN PRESSURE CONTROL (CONTINUED)

The RGE has two modes, minimum speed and cut-off (230 V models only). The RGE is intended to be operated 

in the cut-off mode. This mode is selected by the changeover switch, located inside the enclosure. By placing the 

switch in the cut-off mode, when pressure is below the setpoint value, the fan motor will be turned off and remain 

off until the pressure increases above the setpoint value.

 

9.4 

RGE ELECTRONIC FAN PRESSURE CONTROL SETPOINT ADJUSTMENT

The RGE is factory set for use with R-507 and will energize the fan at minimum speed when the high-side pressure 

rises above 190–200 psig. The fan motor should operate at full speed (1,075 rpm) when the high-side pressure rises 

above 230–240 psig. This setting should be verified on initial startup.

To verify RGE operation, connect the high side of a manifold gauge to the liquid line service valve (P6). Energize 

the condensing unit and monitor the fan operation in accordance with the high-side pressure. In low ambient 

conditions, the condenser may have to be partially blocked to increase high-side pressure.

To adjust the pressure range, remove the RGE cover and locate the adjustment screw (see Figure 5). To increase 

the pressure range, turn the adjustment screw clockwise. To lower pressure range, turn the adjustment screw 

counterclockwise. One turn of the adjustment screw will change the range by approximately 15 psig.

 

 

FIGURE 6: RGE ELECTRONIC FAN PRESSURE CONTROL

 

9.5 

OFF-CYCLE FAN PRESSURE SWITCH

The off-cycle fan pressure switch is designed to protect the evaporator and the condensing unit from over pressure 

during the wash cycle. The off-cycle switch will operate the fan at full speed if high side pressure rises above 270 

psig and operate until pressure falls below 220 psig.

19

Cutoff Mode Switch 

(230 V Models Only)

2

1

4

3

(CW)

Increase

the Set

Value

Decrease

the Set

Value

(CCW)

CSA

DFE0158

Adjustment Screw

Min

Speed

Cut

Off

160

Содержание 8824390















































Отзывы:

Нет отзывов