Mudd-Ox VEN22 Скачать руководство пользователя

Страница: 99 / 100

Towing

Tow Points

1. The rear hitch can serve as a tow point. Push the closed loop of the tow strap inside the hitch, then install the

hitch pin inside the loop (A in Figure-1). This will keep the strap from sliding out.

Note:

For safety measures,

never

attempt to tow from the (2) safety chain mounts shown as “B” in Figure-2, nor install a ball hitch and wrap the

strap around it for towing. These actions may result in serious injury or death.

2. If equipped with optional Bearing Extension Kit, Figure-2 under

Transportation

shows wrapping a strap around

the bearing boxes.

3. If equipped with optional Transport Tie Downs, Figure-3, 4 under

Transportation

shows hooking a strap to the

tie downs.

Pin through the strap loop

Figure-1

Warnings

• Do NOT pull from the roll bar, or any other points than noted above. Excessive stress in poor points can cause the

vehicle to roll over.

• Keep the tow strap away from tires, as it can get wrapped around the axle.

• Always tow at 5 mph or slower.

Vengeance is Operational

If the Vengeance is completely operational, simply put both shifter levers in neutral position. Ensure parking brake

is not engaged. Select your available method of tow points, then proceed.

Vengeance is Inoperable

Put both shift levers into neutral position, disengage parking brake and ensure that the vehicle can freely move. If

it does not, set the parking brake, remove the lower seats, floor boards and engine cover. Look for the following:

• Broken chain: Remove from vehicle.

• Seized bearing: Remove the chain that connects the accompanying axle/jackshaft to the rest of the drivetrain. If

an axle is seized, it will remain seized, however the others will be able to turn freely.

• Transmission seized: Remove the (2) chains that connect directly to the transmission.

• Debris in the drivetrain: Remove from vehicle.

With the debris/chain(s) removed from the vehicle, it should now freely roll and can be towed. Remember to dis-

engage the parking brake, and if the transmission is still connected to the driveline, put the shift levers into neutral.

Proper Hitch Towing

Figure-2

Содержание VEN22





































































































Результаты поиска

Содержание VEN22

Отзывы:

Похожие инструкции для VEN22

Бренды по названию

Популярные бренды

Mudd-Ox VEN22, Руководство пользователя

Результаты поиска

Содержание VEN22

Отзывы:

Похожие инструкции для VEN22

Бренды по названию

Популярные бренды