MTU 8V4000M*3 series Скачать руководство пользователя страница 196 | Manualshive

Страница: 196 / 260

background image

8.15 Oil Filtration / Cooling

8.15.1 Engine oil filter – Replacement

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Filter wrench

F30379104

Engine oil
Oil filter

(→ Spare Parts Catalog)

DANGER

Components are moving or rotating.
Risk of crushing, danger of parts of the body being caught or pulled in!
• Operate the engine at low load only. Keep clear of the danger zone of the engine.

WARNING

High level of engine noise when the engine is running.
Risk of damage to hearing!
• Wear ear protectors.

WARNING

Oil is hot.
Oil can contain residue/substances which are harmful to health.
Risk of injury and poisoning!
• Allow the product to cool to below 50 °C before beginning work.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

NOTICE

Damage to component!
Severe material damage!
• For filter replacement with the engine running, operate the engine at low engine load.
• The filter which is to be replaced must be cut out for a brief period only.

Engine oil filter – Replacement

1.

Stop engine (→ Page 92) and disable engine
start.

2.

Unscrew engine oil filter using filter wrench.

3.

Clean sealing surface on connecting piece.

4.

Check condition of the new engine oil filter
sealing ring and coat it with engine oil.

5.

Fit SOLAS shield

(REFDM TARGET NOT FOUND)

.

6.

Screw on engine oil filter and tighten by
hand.

7.

Replace other engine oil filters in the same
way.

8.

Crank engine on starting system after every
engine oil change and filter replacement
(→ Page 143).

9.

Check engine oil level (→ Page 189).

194 | Oil Filtration / Cooling | MS15034/00E 2018-08

TIM-ID: 0000014238 - 009

«
...
194
195
196
197
198
...
»

Содержание 8V4000M*3 series





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8V4000M*3 series

Бренд: M+S Страницы: 6

Бренд: Kohler Страницы: 108

Бренд: EuroLite Страницы: 19

Command Pro CH940-CH1000

Бренд: Kohler Страницы: 16

Бренд: D-MOTOR Страницы: 48

Automate RF 500 Series

Бренд: Acmeda Страницы: 8

Бренд: Tecumseh Страницы: 94

Бренд: Chery Страницы: 55

Бренд: ZAFFER Страницы: 28

Бренд: YARDMAX Страницы: 25

Бренд: Siemens Страницы: 4

SIMOTICS A-1FV5

Бренд: Siemens Страницы: 66

Бренд: Siemens Страницы: 56

SIMODRIVE POSMO A

Бренд: Siemens Страницы: 58

Бренд: Siemens Страницы: 100

Simotics HV C 1NA14544WA600AG0-Z

Бренд: Siemens Страницы: 112

SIMOTICS DP 1PC13

Бренд: Siemens Страницы: 100

SIMOTICS DP 1PC134

Бренд: Siemens Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды