manualshive.com logo in svg

MTU 20V4000G44F, Руководство по эксплуатации

Поделиться
Скачать
MTU 20V4000G44F Скачать руководство пользователя страница 116

Installing injector, replacing
rings

Note:

• Replace sealing ring (1) between injector

and water sleeve whenever the injector is
disassembled.

• Make sure that the sealing ring (consisting

of CE-ring and support ring) is correctly
seated: The closed CE-ring side must be
abut on the injector, and the protruding
(open) CE-ring side must face towards the
combustion chamber.

• A multi-purpose grease without solids con-

tent must be used.

1.

Install new sealing ring (1) abutted to (Multi-
purpose grease) and ensure that the installa-
tion position is correct.

Note:

Only remove plug from injector just before
assembling the adapter.

2.

Remove plug.

3.

Clean sealing face on cylinder head and pro-
tective sleeve by removing carbon deposits
with a milling cutter.

4.

Fit damper ring (2) on injector and apply (As-
sembly compound (Molykote P 37)).

5.

Fit new O-rings (5, 3) on injector and apply
(Assembly compound (Kluthe Hakuform
30-15)).

Note:

Make sure that the sealing ring (4) does not
fall into the coolant sleeve.

6.

Ensure that the sealing ring (4) is correctly
seated.

7.

Insert injector (1) in the cylinder head, ensur-
ing that it is correctly aligned with the HP line
connection.

8.

Press in injector with installation/removal jig.

9.

Remove installation/removal jig.

114 | Injector | MS15058/04E 2018-12

TIM-ID: 0000079050 - 005

Содержание 20V4000G44F



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды