MTU 20 V 4000 G23 Скачать руководство пользователя страница 138

Страница: 138 / 178

Task Description

133

6.13.2

Centrifugal oil filter – Cleaning and filter-sleeve replacement

Preconditions

• Engine is stopped and starting disabled.

Special tools

Designation / Use

Part No.

Qty.

Torque wrench 6-50 Nm

F30027336

Material

Designation / Use

Part No.

Qty.

Cleaner Hakutex 60

Spare parts

Designation / Use

Part No.

Qty.

Filter sleeve
Sealing ring
Sealing ring

WARNING

Hot oil.

Oil can contain combustion residues which are harmful to health.

Risk of injury and poisoning!

• Wear protective clothing, gloves, and goggles / safety mask.

• Avoid contact with skin.
• Do not inhale oil vapor.

WARNING

Compressed air.

Risk of injury!

• Do not direct compressed-air jet at persons.
• Wear protective goggles / safety mask and ear protectors.

Centrifugal oil filter – Cleaning and filter-sleeve
replacement

1. Remove clamp (3).
2. Release Tommy nut (1) and take off cover (2).
3. Carefully lift rotor (6), allow oil to drain and remove

from housing.

4. Holding the rotor (6) firmly, release rotor cover

nut (7).

5. Take off rotor cover (8).
6. Remove filter sleeve (10).
7. Measure thickness of oil residues on filter sleeve

(10).

8. If maximum layer thickness of oil residues exceeds

45 mm, shorten maintenance interval.

9. Disassemble rotor tube (11), conical disk (12)

and rotor base (14).

10. Wash rotor cover (8), rotor tube (11), conical disk

(12) and rotor base (14) with cleaner.

M015715/00E 06-08

Содержание 20 V 4000 G23



















































































































































































Результаты поиска

Содержание 20 V 4000 G23

Отзывы:

Бренды по названию

Популярные бренды

MTU 20 V 4000 G23, Техническая публикация

Результаты поиска

Содержание 20 V 4000 G23

Отзывы:

Бренды по названию

Популярные бренды