background image

 

Each pressing of the Stop button and restarting with the Start button during

 

its operation time will cause the stove to reenter the firing up phase. 

Switching the device off  

The  heater  is  switched  off  by  pressing  the 

Stop

  button  on  the  control  panel, 

which  switches  off  the  fuel  pump.  The  heater  fan  operates  until  the  furnace  temperature  drops 

below 35°C (

Damping

). When this happens, the stove comes back to the 

Stop

 phase. 

The  device must not be disconnected  from the  power supply during the  fan  operation  - wait 
until the stove has cooled down. The stove switches off automatically. Please note that after 
the device has switched off, the cast iron bowl maintains a higher temperature for some time 
(depending on the ambient temperature) and stove cannot be fired up again until it cools down! 

Maintenance 

The  heater  requires  little  maintenance  activity.  Following  the  producer’s  indications 

in this area will ensure safe and failure-free operation of the device: 

 

clean  the  furnace  bowl  and  other  combustion  chamber  elements  everyday  before  firing  up. 

The  maximal  device  operation  time  without  cleaning  the  bowl  is  about  7-12  hours  (depending 

on the employed oil intended for combustion), 

 

check the passability of the overflow pipe (the pipe in the lower part of the combustion chamber, 

directly over the overflow bowl), clean if necessary. 

 

clean the combustion chamber base (the element under the furnace bowl) at least once a week, 

 

check  whether  the  air  inlet  openings  in  the  lower  and  upper  part  of  the  combustion  chamber 

are not blocked, 

 

clean the rubber duct feeding oil onto the furnace bowl at least once a week, 

 

clean the fuel tank and oil pump filter during the heating season, 

 

if  the  stove  is  going  to  be  off  for  a  longer  time,  carefully  clean  the  combustion  chamber  and 

the furnace bowl and protect them against corrosion by coating them with a thin layer of oil. 

IT IS ADVISED TO CONDUCT SEASONAL INSPECTIONS

 

IN AN AUTHORISED SERVICE CENTRE 

CAUTION!!! 

DUE TO EXHAUST DUST ACCUMULATING 

 

IN THE PIPE EXCHANGER, IT IS ADVISABLE TO CLEAN IT

 

AT LEAST ONCE A YEAR BEFORE THE HEATING SEASON! 

Содержание 52












Отзывы: