MTHTrains 20-20701-1 Скачать руководство пользователя страница 44

Страница: 44 / 49

BL-2 Diesel Engine

Start-up

Solution

When I apply power to the track my engine

doesn't do anything. No lights, no sound, no

nothing.

This is normal. You have to hit the Start-Up

button.

Check to see if that section of track has power.

Use a voltmeter or a lit passenger car, not your

tongue.

Slide the engine a couple of feet in either direc

tion, you may have a bad track section
Have you got that section electrically isolated

with a toggle switch or other device?

I get an error when I hit Start-Up

Have you recently changed the engine address?

Check if there is power on that section of track

the engine is sitting on (there has to be power

for the signal to get to the engine and for the

engine to be able to hear it)

DCS is polarity sensitive when powered by a DC

power supply.

Check the polarity of the DC power supply

connected to the Fixed 1 or Fixed 2 Inputs. Shut

down power, reverse the inputs and repower

DCS. Hitting the startup button on the DCS

remote should start up the engine.

If you have two engines on the track they both

may have the same address. Take one of them

off the rails and try it again

Sound

Solution

When I press the Whistle Button on my DCS

remote or DCS commander the whistle doesn't

blow

Check if the playable whistle is active. On the

DCS Commander there will be two dashes on

the right side of the LCD if it's active. Press “A1”

twice to ensure it's turned off. On your DCS

remote press the “SPW” button twice to ensure

it's disabled

I have no sound on my engine, but my lights are

on and it moves just fine

You may have it turned off. Repeatedly press

VOL + to bring the Master Volume up
Did you turn off the ENG Sounds? Press the

ENG SND button on your DCS controller.
Check that you haven't lowered any of the

independent engine volumes (Eng Sounds, Bell,

Whistle, or Accent)

There's a crackling sound from my engine

Check to see if a screw or some other material

has lodged itself in the underside of the engine.

When I run Doppler I can hear the Doppler shift

but then the engine sounds fade out and I can't

get them back

This is normal. You will need to press the

Doppler button again to turn Doppler off. Your

engine sounds will now return to normal

Smoke

Solution

My engine isn’t smoking at all

Press the smoke button, this will activate the

smoke

DCS (Remember, it’s NOT DCC)

Содержание 20-20701-1


















































Результаты поиска

Содержание 20-20701-1

Отзывы:

Похожие инструкции для 20-20701-1

Бренды по названию

Популярные бренды

MTHTrains 20-20701-1, Руководство оператора

Результаты поиска

Содержание 20-20701-1

Отзывы:

Похожие инструкции для 20-20701-1

Бренды по названию

Популярные бренды